Download  Print this page

Using The Snmp; Inquiry Commands - Sony SNC-EP520 User Manual

Hide thumbs

Advertisement

Record event: Type of event used for the
recording: Sensor input, Camera tampering
detection, Motion detection, Network
disconnection.
Playing a video/audio file
Click
(start) to start playback from the beginning of
the selected file.
To freeze the movie temporarily, click
Click
again to resume playback from the freeze
point.
To stop playback, click
To start playback from the beginning, click
again.
Playback stops when the file is played to the end.
Playing from a specified point
Move the slider bar below the image display, and
playback will start from the position of the slider bar.
Adjusting the sound
Adjust the playing sound volume by moving the
slider bar. Move it to the left end for minimum volume,
and to the right end for maximum volume.
Click
(speaker) to enable/disable sound (muting).
When sound muting is on, no sound will be heard, even
if you move the slider bar.
Saving an image
Click the
(capture) icon during playback or pause
and the captured image is displayed in a pop-up dialog.
To save the image, click Save on the dialog. You can
specify the destination to which the image is to be
stored, and select the JPEG or Bitmap format.
How to change the image display size
Click × 1/4, × 1/2, × 1, × 2 or Full at the top of the image
to display the image in the selected magnification.
If you select × 1, the image is displayed in the
original image display size of the file.
The × 2 button is only available when image size is
640 × 480 (VGA) or smaller.
The selected image display size is highlighted.
Note
If the name of the folder in which a playable file is saved
ends with a number, the file may stop in the middle of
playback. If this occurs, change the name of the folder
so that it does not end with a number.
92

Using the SNMP

(pause).
(stop).
(start)
Using the SNMP
This unit supports SNMP (Simple Network
Management Protocol). You can read MIB-2 objects
using software such as SNMP manager software. This
unit also supports the coldStart trap which occurs when
the power is turned on or the unit restarts, and the
Authentication failure trap, which informs of any illegal
access using SNMP.
Using CGI commands, you can set the community name
and access limitation, host to send traps, and some MIB-
2 objects. To allow these settings, you need
authentication by the camera administrator.

1. Inquiry Commands

You can check the SNMP Agent settings using the
following CGI commands.
<Method>
GET, POST
<Command>
(JavaScript parameter format)
(standard format)
With the above inquiry, you can obtain the following
setting information. The following explains the setting
information using the inqjs=snmp (JavaScript
parameter) format.
var sysDescr="Model name"
var sysObjectID="1.3.6.1.4.1.122.8501"
var sysLocation=""
var sysContact=""
var sysName=""
var snmpEnableAuthenTraps="1"
var community="1,r,public,0.0.0.0,v2c"
var community="2,r,private,192.168.0.101,v2c" ...8
var trap="1,public,192.168.0.101,v2c"
1 describes the case of "mib-2.system. sysDescr.0".
You cannot change this parameter.
2 describes the case of "mib-2.system.
sysObjectID.0". You cannot change this parameter.
3 describes the case of "mib-2.system.
sysLocation.0". This field is used to describe
information on the location of this camera. Nothing
is set at the factory.
...1
...2
...3
...4
...5
...6
...7
...9

Advertisement

Table of Contents

   Related Manuals for Sony SNC-EP520

Comments to this Manuals

Symbols: 0
Latest comments: