Additional Safety Rules; Operating Instructions - Makita HP2032 Instruction Manual

ENGLISH
1 Grip base
2 Side grip (auxiliary handle)
3 Teeth
4 Protrusions
5 Loosen
6 Tighten
SPECIFICATIONS
Model
Max. capacities
Concrete ......................................................... High: 20 mm
Steel ............................................................... High: 8 mm
Wood .............................................................. High: 25 mm
No load speed (RPM) ....................................... High: 0 – 2,900
Blows per minute .............................................. High: 0 – 32,000
Overall length ............................................................. 370 mm
Net weight ................................................................... 2.5 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear pro-
tectors and thickly padded gloves.
2. Under normal operation, the machine is
designed to produce vibration. The screws
can come loose easily, causing a breakdown
or accident. Check tightness of screws care-
fully before operation.
3. Always be sure you have a firm footing. Be
sure no one is below when using the machine
in high locations.
4. Hold the machine firmly with both hands.
Always use the side grip.
5. Keep hands away from rotating parts.
6. Do not leave the machine running. Operate the
machine only when hand-held.
Explanation of general view
7 Bit
8 Chuck key
9 Sleeve
0 Ring
q Depth gauge
w Switch trigger
HP2032
Low: —
Low: 13 mm
Low: 40 mm
Low: 0 – 850
Low: 0 – 9,400
7. When drilling into walls, floors or wherever
''live'' electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE
MACHINE! Hold the machine only by the insu-
lated grasping surfaces to prevent electric
shock if you drill into a ''live'' wire.
8. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Important:
Always be sure that the machine is switched off and
unplugged before installing or removing the side grip,
bit or other accessories.
Side grip (auxiliary handle) (Fig. 1)
Always use the side grip to ensure operating safety.
Install the side grip so that the teeth on the grip fit in
between the protrusions on the machine barrel. Then
tighten the grip by turning clockwise at the desired
position. It may be swung 360° so as to be secured at
any position.
Installing or removing drill bit
For HP2032 and HP2034 (Fig. 2)
To install the bit, place it in the chuck as far as it will
go. Tighten the chuck by hand. Place the chuck key in
each of the three holes and tighten clockwise. Be sure
to tighten all three chuck holes evenly.
To remove the bit, turn the chuck key counterclock-
wise in just one hole, then loosen the chuck by hand.
After using the chuck key, be sure to return it to the
original position.
e Lock button
r Reversing switch lever
t Speed change knob
y Action mode change knob
u Blow-out bulb
i Vent holes
HP2033 HP2034
20 mm 20 mm
— —
8 mm 8 mm
13 mm 13 mm
25 mm 25 mm
40 mm 40 mm
0 – 2,900 2,900
0 – 850 850
0 – 32,000 32,000
0 – 9,400 9,400
368 mm 370 mm
2.5 kg 2.5 kg
5