Specifications; Snooze Function; Display Illumination; Maintenance - Makita BMR100 Instruction Manual

Display will appear
been set.

Snooze function

1. Whilst the alarm is activated, pressing any buttons
except the Power Button will activate the snooze
function. The radio or HWS buzzer alarm will be
silenced with interval of 5 minutes.
2. The display will flash both the snooze symbol
the alarm symbol. The snooze function can be
repeatedly during one hour that the alarms are active.

Sleep function

The sleep timer will automatically switched off the radio
after a preset time has elapsed.
1. Press and continue to hold down the Power button for
more than 2 seconds, followed by a beep tone, the
display will cycle through the available sleep times in
the order 60-45-30-15-120-90-60.
Release the Power button when the required sleep
time appears in the display. The
appear in the display and the radio will play the last
station selected.
2. To cancel the sleep function, press the Power button.
The Symbol will disappear and radio is off.

Display illumination

Press any buttons or rotate tuning/volume control will
illuminate the LCD display for approx. 15 seconds. During
scanning stations and alarm activated, will also
automatically illuminate the display.
Setting tuning step
Tuning steps on some countries are different from where
you purchase the radio. If you buy the radio in Europe and
intend to use in Northern America or some Southern
American countries, you may have to adjust tuning step
so the radio may continue to serve you well.
While radio is switched off, long pressing Step/Band
button for more than 2 seconds will first show current FM
tuning step.
Continue pressing Step/Band button for approx. another
5 seconds until display FM and 50 kHz (tuning step)
flashing followed by a beep. By rotating the Tuning
control, you may adjust to 100 kHz per tuning step.
After FM tuning step is reset, pressing Step/Band button
again, display will show AM (MW) and flash 9 kHz. By
rotating Tuning control, you may adjust to 10 kHz per
tuning step. Complete the setting by pressing Step/Band
button.
Change Stereo to Mono
When the stereo FM station reception is weak, you can
improve it by pressing Mono button for 2 seconds. The
sound is no longer in stereo and stereo indicator
disappears.
when buzzer alarm has
and
symbol will
How to play other audios
CAUTION:
Unplug this apparatus before connecting other
audios.
• There are 2 AUX in sockets. AUX 1 is located on the
front panel, and AUX 2 is located in the battery
compartment.
• Connect a stereo or mono source (i.e. iPod, MP3, or
CD player) to either AUX 1 or AUX 2 by audio cord.
• Repeatedly press and release the BAND button until
AU1" or "AU2" is displayed, then AUX function is
activated.
• AUX can't be activated as alarm source.

MAINTENANCE

CAUTION:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.

Specifications:

Power Requirements
AC power adaptor DC12V 700mA, center pin positive
Battery UM-3 (AA size) x 2 for back up
Cluster battery: 9.6 - 18V
Slide battery: 9.6 - 24 V
Frequency coverage FM 87.50 - 108 MHz
AM (MW) 522 - 1629 kHz
(9 kHz/step)
Circuit feature
Loudspeaker 3 inches 8 ohm
Output Power 9.6V: 0.8 W x 2, 12V: 1.2 W x 2
14.4V: 2W x 2, 18V: 3W x 2
24V: 5W x 2
Input terminal 3.5 mm dia. (AUX IN1/AUX IN2)
Antenna system FM: soft bended rod antenna
AM: bar antenna
Dimension (W x H x D) in mm
263 x 305 x 166
Weight 4.2kg (without battery)
7