Download  Print this page

Pioneer ND-BC20PA Installation Manual page 6

Hide thumbs
   

Advertisement

① Image processing unit power supply
③ RCA power supply
⑩ Button unit
⑨ Button unit
cable connector
connector
② Rear view camera
connector
4 m (13 ft. 2 in.)
④ Rear view camera
3 m (9 ft. 10 in.)
⑤ RCA pin
⑦ Fuse (1A) 3 m (9 ft. 10 in.)
⑥ Red
7 m (23 ft.)
1.5 m (4 ft. 11 in.)
⑧ Black
Fig. 16
Abb. 16
⑤ Image processing unit power supply
② Rear view
camera
① Plastic clamps
⑥ Button unit
④ Product with a video input
jack (Hideaway unit etc.)
③ RCA power
supply cable
⑦ Made with a rasp etc.
⑧ Scuff plate
⑪ Double-sided
tape (rectangular)
⑨ Plastic clamp
⑩ Waterproof plate
Fig. 17
Abb. 17
① Pull out from here
② Hinge
③ Harness cover
④ Rear view
camera
⑤ Hatch
Fig. 18
Abb. 18
① Rear view camera
② Hatch
③ Cord
Fig. 19
Abb. 19
② Waterproof pad
① Plastic clamp
④ Make a U-shaped loop in
the lead outside the rubber
packing to prevent rain-
water from flowing along
③ Rubber packing
the lead into the interior
of the vehicle.
Fig. 20
Abb. 20
Connection
<ENGLISH>
Note:
Accessory power supply
• This unit is for vehicles with a 12-volt battery and
To electric terminal controlled by ignition
negative grounding. Before installing it in a recreational
switch (12 V DC) ON/OFF.
vehicle, truck, or bus, check the battery voltage.
• To avoid shorts in the electrical system, be sure to
⑥ Red
disconnect the
battery cable before beginning
⑦ Fuse (1A)
installation.
• Refer to the owner's manual for details on connecting the
Ground
other units, then make connections correctly.
• Secure the wiring with cable clamps or adhesive tape. To
To vehicle (metal) body.
protect the wiring, wrap adhesive tape around them where
⑧ Black
they lie against metal parts.
• Route and secure all wiring so it cannot touch any
Cord installation (Fig. 17)
moving parts, such as the gear shift, handbrake and seat
rails. Do not route wiring in places that get hot, such
① Plastic clamps
as near the heater outlet. If the insulation of the wiring
② Rear view camera
melts or gets torn, there is a danger of the wiring short-
circuiting to the vehicle body.
③ RCA power supply cable
• Do not shorten any leads.
④ Product with a video input jack
• Never feed power to other equipment by cutting the
(Hideaway unit etc.)
insulation of the power supply lead of the unit and
⑤ Image processing unit power supply
tapping into the lead. The current capacity of the lead will
⑥ Button unit
be exceeded, causing over heating.
• When replacing the fuse, be sure to only use a fuse of the
⑦ Made with a rasp etc.
rating prescribed on the fuse holder.
⑧ Scuff plate
• To minimize noise locate the TV antenna cable, radio
⑨ Plastic clamp
antenna cable and RCA power supply cable as far away
⑩ Waterproof plate
from each other as possible.
⑪ Double-sided tape (rectangular)
• Connection to a TV with an RCA video input is possible,
but confirm whether the TV you use has a reverse gear
Cord installation points (Fig. 18)
connection function.
• If this unit is installed in a vehicle that does not have an
ACC (accessory) position on the ignition switch, the red
• When pulling the cord out of the car,
lead of the unit should be connected to a terminal coupled
pull from the outer side of the hatch
with ignition switch ON/OFF operations. If this is not
done, the vehicle battery may be drained when you are
harness cover and hinge.
away from the vehicle for several hours.
① Pull out from here
② Hinge
③ Harness cover
④ Rear view camera
⑤ Hatch
After cord installation (Fig. 19, Fig. 20)
• Open and close the hatch door slowly
ACC position
No ACC position
to confirm that the cord is not rubbing
against the rim of the door.
① Rear view camera
• Cords for this product and those for other products may
② Hatch
be different colors even if they have the same function.
③ Cord
When connecting this product to another product, refer to
the supplied manuals of both products and connect cords
• When the rear view camera cord cannot
that have the same function.
be pulled out from the lower side due to
the type of car.
Connection sample (Fig. 16)
As shown in the figure 18, bend the cord
into a U shape in front of the waterproof
① Image processing unit power supply
pad, making sure that rain water cannot
② Rear view camera connector
③ RCA power supply cable connector
enter the car by running down the cord.
④ Rear view camera
① Plastic clamp
⑨ Button unit
② Waterproof pad
③ Rubber packing
⑩ Button unit connector
④ Make a U-shaped loop in the lead outside
Video input jack
the rubber packing to prevent rainwater from
Connect to video input jack.
flowing along the lead into the interior of the
⑤ RCA pin
vehicle.

Advertisement

loading

  Related Manuals for Pioneer ND-BC20PA