Download  Print this page

Specifications; Contact With Liquid; Questions And Answers - Siemens Gigaset A260 Manual

Hide thumbs

Advertisement

Table of Contents
Changing pause after line seizure
You can set the length of the pause inserted
between pressing the talk key
phone number.
¢
¢
I I O 1 O
MENU
pause length flashes: 1 = 1 sec.; 2 = 3 sec.; 3 = 7 sec.
¢
¢
Enter number
Changing the pause after the recall key
¢
¢
I I O 1 4
MENU
pause length flashes: 1 = 800 ms; 2 = 1600 ms;
¢
Enter number
3 = 3200 ms
Appendix
Entering special characters
Standard characters
1x
2x
1
1
Space
Q
.
,
P
*
/
#
Abc-->
123-->
123
abc

Specifications

Recommended battery pack
(Valid at the time of going to press)
Nickel-metal-hydride (NiMH):
Handset A16: V30145-K1310-X383
Handset A26: V30145-K1310-X359, X402
The handset is supplied with the recommended
battery pack.
Base station power consumption
In standby mode: approx. 2W
During a call: approx. 3W
General specifications
DECT standard
GAP standard
Range
Base station power supply 230 V ~/50 Hz
Environmental conditions
in operation
c
and sending the
The number for the current
.
OK
The number for the current
¢
.
OK
3x
4x
5x
£
$
¥
?
!
0
(
)
<
#
@
\
is supported
is supported
up to 300 m outdoors,
up to 50 m in buildings
+5 °C to +45 °C;
20% to 75% humidity
9
Care
Wipe the base station and handset with a damp
cloth (no solvents) or an antistatic cloth.
Never use a dry cloth. This can cause static.

Contact with liquid

If the handset has come into contact with liquid:
Switch off the handset and remove the bat-
tery pack immediately.
Allow the liquid to drain from the handset.
Pat all parts dry, then with the battery compart-
ment open and the keypad facing down place
the handset in a dry, warm place for at least
72 hours (not in a microwave, oven etc.).
Do not switch on the handset again until it is
completely dry.
When it has fully dried out, you will normally be
6x
able to use it again.
¤

Questions and answers

+
=
If you have any queries about the use of
&
your phone, you can contact us any time at
www.siemens.com/gigasetcustomercare.
The table below contains a list of common
problems and possible solutions.
Problem
Nothing
appears in the
display.
No reaction to
keystroke.
No wireless
connection to
the base sta-
tion, Base
flashes in the
display.
!
Cause
Solution
The handset is not
Press the end call key
a
switched on.
for approx. 5 sec.
or place the handset
in the base station.
Charge/replace the
Battery pack is
battery pack (page 3).
flat.
The key lock is
Press the hash key
activated.
for approx. 2 sec.
(page 1).
The handset is
Move the handset
outside the range
closer to the base
of the base sta-
station.
tion.
The handset is not
Register the handset
registered.
(page 3).
The base station is
Check the power
not switched on.
connector at the base
station (page 2).
Cords not routed
Check cord routing
correctly
(page 2).
R

Advertisement

Table of Contents
loading

  Also See for Siemens Gigaset A260

This manual is also suitable for:

Gigaset a165Gigaset a160Gigaset a265