Explanation Of General View; Specifications - Makita LS1016 Instruction Manual

ENGLISH
(Original instructions)
1 Stopper pin
2 Hex bolt(s)
3 Blade guard
4 Kerf board
5 Saw blade
6 Blade teeth
7 Left bevel cut
8 Straight cut
9 Right bevel cut
10 Lock lever
11 Locking screw
12 Adjusting bolt
13 Turn base
14 Stopper lever
15 Slide pipe
16 Top surface of turn base
17 Periphery of blade
18 Guide fence
19 Adjusting screw
20 Stopper arm
21 Grip
22 Cam
23 Lever(s)
24 Latch lever
25 Scale plate
26 Release button
27 Pointer
28 Lock-off button
29 Switch trigger
30 Hole for padlock
31 Switch for light
32 Light
33 Switch for laser
34 Wrench holder

SPECIFICATIONS

Model
Blade diameter
For all countries other than European countries ............................................................................. 255 mm – 260 mm
For European countries.................................................................................................................................... 260 mm
Blade body thickness ........................................................................................................................... 1.6 mm – 2.4 mm
Hole diameter
For all countries other than European countries ............................................................................................. 25.4 mm
For European countries...................................................................................................................................... 30 mm
Max. cutting capacities (H x W) with 260 mm in diameter
Miter angle
0°
45° (right and left)
52° (right and left)
60° (right)
16

Explanation of general view

35 Hex wrench
36 Center cover
37 Hex socket bolt
38 Shaft lock
39 Blade case
40 Arrow
41 Outer flange
42 Ring
43 Inner flange
44 Socket wrench
45 Spindle
46 Dust nozzle
47 Dust bag
48 Fastener
49 Dust box
50 Cover
51 Button
52 Cylinder section
53 Sawdust
54 Support
55 Turn base
56 Clamping screws
57 Upper fence
58 Lower fence
59 Red indicating area
60 Vise knob
61 Vise arm
62 Vise rod
63 Screw
64 Vise plate
65 Vise nut
66 Holder
67 52/38° type crown molding
68 45° type crown molding
45° (left)
42 mm x 310 mm
58 mm x 279 mm
42 mm x 218 mm
58 mm x 197 mm
–
–
69 45° type cove molding
70 Inside corner
71 Outside corner
72 Crown molding stopper L
(Optional accessory)
73 Crown molding stopper R
(Optional accessory)
74 Crown molding stopper L
75 Crown molding stopper R
76 Crown molding
77 Vise
78 Spacer block
79 Aluminum extrusion
80 Cut grooves with blade
81 Triangular rule
82 Miter scale
83 Bevel scale plate
84 0° angle adjusting bolt
85 Top surface of turn table
86 Scale plate
87 Left 45° bevel angle adjusting
bolt
88 Right 45° bevel angle adjusting
bolt
89 Workpiece
90 Laser line
91 Vertical vise
92 Screwdriver
93 Screw (one piece only)
94 Lens for the laser light
95 Limit mark
96 Brush holder cap
LS1016/LS1016L/LS1016F/LS1016FL
Bevel angle
0°
68 mm x 310 mm
91 mm x 279 mm
68 mm x 218 mm
91 mm x 197 mm
68 mm x 190 mm
91 mm x 171 mm
68 mm x 155 mm
91 mm x 139 mm
45° (right)
29 mm x 310 mm
43 mm x 279 mm
29 mm x 218 mm
43 mm x 197 mm
–
–