Specifications - Makita 3708 Instruction Manual

ENGLISH
(Original instructions)
1 Lever
2 Scale
3 Bit protrusion
4 Adjusting roller
5 Wing bolt
6 Graduation
7 Trimmer shoe
8 Amount of chamfering
9 Base
10 Switch lever
11 Loosen
12 Tighten
13 Hold
14 Bolt

SPECIFICATIONS

Model
Collet chuck capacity.................................................................... 6 mm or 1/4"
–1
No load speed (min ).................................................................. 35,000
Overall length ............................................................................... 308 mm
Net weight .................................................................................... 1.3 kg
Safety class ..................................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future refer-
ence.
6
Explanation of general view
15 Flat washer (large)
16 Flat washer (small)
17 Spring washer
18 Wing nut
19 Workpiece
20 Bit revolving direction
21 View from the top of the tool
22 Feed direction
23 Straight guide
24 Screws
25 Screwdriver
26 Templet guide
27 Convex portions
28 Straight bit
TRIMMER SAFETY WARNINGS
1.
ENE010-1
2.
ENF002-2
3.
4.
5.
6.
GEA010-1
7.
8.
9.
10. Before using the tool on an actual workpiece, let
11. Be careful of the bit rotating direction and the
12. Do not leave the tool running. Operate the tool
13. Always switch off and wait for the bit to come to
14. Do not touch the bit immediately after operation;
15. Do not smear the tool base carelessly with thin-
29 Templet
30 Distance (X)
31 Templet guide 10
32 Guide plate
33 Clamp screw (A)
34 Center hole
35 Nail
36 Adjusting screw
37 Clamp screw (B)
38 Trimmer guide
39 Bit
40 Guide roller
41 Limit mark
42 Brush holder cap
3708/3708F
/II
Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
Wear hearing protection during extended period
of operation.
Handle the bits very carefully.
Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
feed direction.
only when hand-held.
a complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your
skin.
ner, gasoline, oil or the like. They may cause
cracks in the tool base.
3708FC
6 mm or 1/4"
26,000
308 mm
1.3 kg
/II
GEB019-4