Download  Print this page

Operation; Switching The Unit On/off - Mitsubishi Electric PEAD-RP1.6EA Operation Manual

Hide thumbs

Advertisement

Table of Contents

2. Operation

CENTRALLY CONTROLLED
CHECK
STAND BY
DEFROST
1
TEMP.
2
3
TIMER SET
PAR-20MAA
D
C
B
CENTRALLY CONTROLLED
E
CHECK
˚C
F
STAND BY
DEFROST
TEMP.
G
H
C
CENTRALLY CONTROLLED
E
CHECK
˚C
STAND BY
DEFROST
TEMP.
1
3
2
TIMER SET
PAR-20MAA
4
1Hr.
ON OFF
˚C
CLOCK
FILTER
CHECK MODE
˚C
TEST RUN
ERROR CODE
FUNCTION
NOT AVAILABLE
ON/OFF
FILTER
CHECK TEST
4 5 6 8 7 9
A
U
T
Q
S
1Hr.
ON OFF
˚C
CLOCK
FILTER
CHECK MODE
TEST RUN
ERROR CODE
FUNCTION
NOT AVAILABLE
ON/OFF
I KL J
A
1Hr.
ON OFF
˚C
CLOCK
FILTER
CHECK MODE
TEST RUN
ERROR CODE
FUNCTION
NOT AVAILABLE
ON/OFF
FILTER
CHECK TEST
6 8 7
Remote controller-Button
1 [Room temperature adjustment] Button
2 [Timer/continuous] Button
3 [Selecting operation] Button
4 [Time selection] Button
[Time-setting] Button
5 [Louver] Button
6 [Fan speed adjustment] Button
7 [Up/down airflow direction] Button
8 [Ventilation] Button
B
9 [Checking/built-in] Button
0 [Test run] Button
A
A [Filter] Button
0
B [ON/OFF] Button
C Position of built-in room temperature sensor
• Never expose the remote controller to direct sunlight. Doing so can re-
C
sult in the erroneous measurement of room temperature.
• Never place any obstacle around the lower right-hand section of the
remote controller. Doing so can result in the erroneous measurement of
room temperature.
Remote controller-Display
A Current time/Timer
B Centralized control
C Timer ON
D Abnormality occurs
E Operation mode:
R
F Preparing for Heating mode
P
G Defrost mode
O
H Set temperature
I Power ON
N
J Louver
M
K Not available function
L Ventilation
M Function setting mode
N Test run mode
O Error check mode
P Filter sign
Q Set effective for 1 hr.
R Sensor position
S Room temperature
T Airflow
U Fan speed
Before starting operation
• Start running after the "HO" display has disappeared. The "HO" display
briefly appears on the room temperature display (max. 3 minutes) when
the power is turned on and after a power failure. This does not indicate
any failure of the air conditioner.
• The operation modes of the indoor units' cooling operation, dry opera-
tion, and heating operation are different from those of the outdoor units.
When the operation is started with cooling/dry (heating) and other in-
A
door units connected to the counterpart outdoor units are already run-
ning in the same operation mode, the remote control displays "
" " ("
") mode. However, the operation comes to stop, and you cannot
B
get a desired mode. When this occurs, you will be notified by the "
" " ("
") display that flashes in the liquid crystal display of the remote
controller. Set to the operation mode of other indoor unit by the opera-
tion switch button.
The above does not apply to the models that simultaneously run both
the cooling operation and heating operation.
• The outdoor units stop when all the indoor units connected to the coun-
terpart outdoor units stop.
• During heating operation, even if the indoor unit is set to operation while
the outdoor unit is in defrosting operation, operation starts after the de-
frosting operation of the outdoor unit has ended.

2.1. Switching the unit on/off

Start an operation
1. Press the B B B B B [ON/OFF] button
Operation lamp
lights up and operation starts.
Stop an operation
1. Press the B B B B B [ON/OFF] button again
Operation lamp goes off and operation stops.
COOL,
DRY,
AUTO,
FAN,
HEAT
" or
" or
3

Advertisement

Table of Contents

   Also See for Mitsubishi Electric PEAD-RP1.6EA

   Related Manuals for Mitsubishi Electric PEAD-RP1.6EA

Comments to this Manuals

Symbols: 0
Latest comments: