Summary of Contents for Yard Machines 260 Thru 279
Page 1
Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722. MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A.
Troubleshooting ... 14 Parts List... 16 This Operator’s Manual is an important part of your new lawn mower. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Before you start assembling your new equipment, please locate the model plate on the equipment and copy the information from it in the space provided below.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
complete stop before removing the grass catcher or unclogging the chute. The cutting blade continues to rotate for a few seconds after the engine is shut off. Never place any part of the body in the blade area until you are sure the blade has stopped rotating.
Page 5
WARNING - YOUR RESPONSIBILITY: understand and follow the warnings and instructions in this manual and on the machine. NOTE: Not all safety labels shown may apply to your lawn mower. Grass catcher components, discharge cover, and trail shield are subject to wear and damage which could expose moving parts or allow objects to be thrown.
Roll or slide unit out of carton and check carton thoroughly for loose parts. Disconnecting Spark Plug Wire Before setting up your lawn mower, disconnect the spark plug wire from the spark plug and ground against the engine. See Figure 1.
SECTION 4: KNOW YOUR LAWN MOWER Read this operator’s manual and safety rules before operating your lawn mower. Compare the illustration in Figure 8 with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
7. To mulch insert the mulch plug/cover on the mower. 8. Before storing the lawn mower for the winter, use stabilizer-treated fuel and run the tank dry. 9. Thirty days before start of the new season, check the air filter, spark plug and blade on the lawn mower, and replace if needed.
• Prime engine as instructed in the separate engine manual packed with your unit. • Your lawn mower may be equipped with a constant speed throttle, which is set at full throttle for best performance. • Stand behind the mower and squeeze the blade control handle against the upper handle.
Changing of engine governed speed will void engine warranty. • The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain the lawn mower as instructed in this manual.
Page 12
Lubrication WARNING: Always stop engine, discon- nect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. Blade Control Handle and Drive Clutch Control: Lubricate the pivot points on the blade control handle and the drive clutch control at least once a season with light oil.
Page 13
Reassemble blade and torque as instructed in previous section. Plastic Off-Season Storage Rivet The following steps should be taken to prepare your lawn mower for storage. • Clean and lubricate mower thoroughly as described in the lubrication instructions. Transmission Pulley...
We do not recommend the use of a IMPORTANT: pressure washer or garden hose to clean your unit. • Refer to engine manual for correct engine storage instructions. • Coat mower’s cutting blade with chassis grease to prevent rusting. • Store mower in a dry, clean area.
Page 17
Model Series 260 thru 279 Ref. Part No. Part Description 747-1214 Drive Control Handle 747-1161A Blade Control Handle 749-1092A Upper Handle 746-1092A Drive Control Cable 746-1113 Blade Control Cable - B&S 746-1132 Blade Control Cable - B&S 746-1114 Blade Control Cable- Tec...
Page 18
Model Series 260 thru 279 Ref. Part No. Part Description 618-0392 Upper Housing Assembly 721-0329 Oil Seal .500 ID x .687 OD 741-0673 Flange Bearing .503 ID x .689 OD 736-0520 Flat Washer .504 ID x .700 OD x .030 736-0711 Flat Washer .504 ID x .700 OD x .035...
Page 20
MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD PROD- UCTS INC (“MTD”) with respect to new merchandise pur- chased and used in the United States, its possessions and territories. MTD warrants this product against defects in material and...