Auto Stay Arming Feature - Honeywell LYNX Touch L5210 Series User Manual

Hide thumbs Also See for LYNX Touch L5210 Series:
Table of Contents

Advertisement

6(&85,1* 7+( 35(0,6(6
6(&85,1* 7+( 35
6(&85,1* 7+( 35
6(&85,1* 7+( 35
$UPLQJ WKH 6\VWHP
Armed Stay
Disarm
10:18 AM June 8, 2010
If an invalid User Code is entered or if a valid user code has not been entered within 10 seconds, the system
will return to the "security" screen and it will not be armed.

Auto Stay Arming Feature

,I WKLV IHDWXUH LV HQDEOHG E\ LQVWDOOHU WKH /<1; 7RXFK ZKHQ DUPHG $:$< IURP WKH FRQWURO·V NH\SDG RU D :LUHOHVV .H\SDG
DXWRPDWLFDOO\ VZLWFKHV WR WKH 67$< PRGH LI WKH ([LW 7LPH H[SLUHV DQG QR H[LW KDV EHHQ PDGH ([LW PXVW EH PDGH WKURXJK
DQ (QWU\ ([LW =RQH GRRU ,I H[LW LV PDGH WKURXJK D *DUDJH 'RRU WKH V\VWHP ZLOO DXWRPDWLFDOO\ VZLWFK WR WKH 67$< PRGH
ZKHQ WKH ([LW 7LPH H[SLUHV
NOTE:
If the exit route entry/exit sensor is in a check condition or has been bypassed it will result in a loss of interior protection because the
alarm system will arm STAY in this case. Consult with your installer for servicing of the entry exit zones or to turn off this feature if a
check condition on entry exit zones occurs.
Arming in Night Stay Mode
8VH WKLV PRGH ZKHQ \RX DUH VWD\LQJ KRPH EXW UHTXLUH LQFUHDVHG VHFXULW\ 7KH PRGH $UPV VDPH DV 67$< PRGH
EXW DOVR DUPV SUHVHOHFWHG LQWHULRU VHQVRUV SURJUDPPHG E\ \RXU LQVWDOOHU ZKLOH RWKHU LQWHULRU VHQVRUV DUH OHIW
GLVDUPHG 7KLV PRGH FDQ EH DUPHG ZKHQ \RX DUH VWD\LQJ KRPH EXW H[SHFW VRPHRQH WR XVH WKH HQWUDQFH GRRU
ODWHU +RZHYHU SHUVRQV HQWHULQJ ODWHU FDQ HQWHU WKURXJK DQ HQWU\ H[LW GRRU EXW WKH\ PXVW GLVDUP WKH V\VWHP
DQG PXVW QRW YLRODWH DQ\ RI WKH SURJUDPPHG LQWHULRU ]RQHV WR DYRLG VRXQGLQJ DQ DODUP &ORVH DOO SURWHFWHG
SHULPHWHU ZLQGRZV DQG GRRUV EHIRUH DUPLQJ 7KH JUHHQ 5HDG\ LQGLFDWRU RQ WKH FRQWURO VKRXOG EH OLW LI WKH
V\VWHP LV UHDG\ WR EH DUPHG :KHQ DUPHG LQ 1LJKW 67$< PRGH WKH V\VWHP ZLOO VRXQG DQ DODUP LI D SURWHFWHG
]RQH LV IDXOWHG EXW \RX PD\ RWKHUZLVH PRYH IUHHO\ WKURXJKRXW WKH SUHPLVHV /DWH DUULYDOV FDQ HQWHU WKURXJK
WKH GHVLJQDWHG HQWUDQFH GRRU ZLWKRXW FDXVLQJ DQ DODUP EXW WKH\ PXVW GLVDUP WKH V\VWHP ZLWKLQ WKH HQWU\
GHOD\ SHULRG RU DQ DODUP ZLOO RFFXU ,I 4XLFN $UP ZDV SURJUDPPHG E\ WKH LQVWDOOHU \RX GR QRW QHHG WR HQWHU WKH
VHFXULW\ FRGH WR DUP WKH V\VWHP 7KH VHFXULW\ FRGH PXVW DOZD\V EH XVHG WR GLVDUP WKH V\VWHP KRZHYHU
When NIGHT-STAY mode is on, the selected interior zones are armed and cause an alarm if anyone enters those
areas (e.g., waking in the middle of the night). To avoid sounding an alarm, you must disarm the system before
any activity takes place in those interior zones.
The Guest Code and Installer Code cannot disarm the system unless it was used to arm the system. In addition,
if the system is armed by pressing via Quick-Arming, neither the Guest Code nor Installer Code can disarm the
system.
Ready To Arm
Arm Away
Arm Stay
Delay
10:18 AM June 8, 2010
(0,6(6
(0,6(6
(0,6(6
4.
System
Zones
Message
Phone
More
5200-100-017-V0
1.
Zones
System
Message
Phone
More
5200-100-014-V0
At the end of the exit delay the system announces
"Armed Stay" and displays the "Armed Stay" screen.
Select the Arm Stay icon, the system beeps once and
displays a keypad.
²
²

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents