Download Print this page

Specifications; Contact With Liquid; Questions And Answers - Siemens Gigaset A410 Manual

Hide thumbs

Advertisement

Appendix
Character set chart
Press the required key the number of times indi-
cated.
1 x
2 x
+
0
Q
Spa ce
1
1
# (appears in display as
R
/
P
*

Specifications

Power consumption
In ready status: approx. 2 Watt. During charging:
approx. 3 Watt. During a call: approx. 2 Watt.
General specifications
Standard
Range
Mains unit
Operating temperature
Dimensions/Handset
Dimensions/Base
Weight/Handset
Weight/Base
Re-chargeable battery
pack
Battery pack re-order
number
Battery pack capacity
Charging time
Calling time
Standby time
Care
Wipe the base station and handset with a damp
cloth or an antistatic wipe. Never use a dry cloth!
This can cause static!
3 x
4 x
5 x
6 x
-
|
?
_
j
)
(
)
,
DECT and GAP compatible
up to 300 m outdoors, up to 50
m indoors
230 V ~/50 Hz
+5 °C to +45 °C
154 x 54 x 30 mm (L × W × H)
87 x 126 x 87mm (L x W x H)
approx. 127 g (including bat-
tery pack)
approx. 121 g
NiMH, 2xAAA Pack
V30145-K1310-X359,
A5B00075178739
550 mAh
approx. 10 hours in base,
approx. 5 hours in desktop
charger
approx. 10 hours
approx. 170 hours (7 days)
7

Contact with liquid

If the handset has come into contact with liquid:
1 Switch the handset off and remove the bat-
tery pack immediately.
2 Allow the liquid to drain from the handset.
3 Pat all parts dry, then place the handset with
the battery compartment open and the keypad
facing down in a dry, warm place for at least
72 hours (not in a microwave, oven etc.).
4 Do not activate the handset again until it is
dry.
When it has fully dried out you will normally be
able to use it again.

Questions and answers

If you have any queries about the use of your tele-
phone, go to
www.siemens-mobile.com/gigasetcustomercare
for assistance 24/7. The table below contains a list
of common problems and possible solutions.
Problem
Cause
Nothing
The handset is not
appears in the
switched on.
display.
Battery pack is
flat.
No response
The keypad lock is
to key press,
activated.
"HOLD KEY"
appears in the
display.
No wireless
The handset is
connection to
outside the range
the base, dif-
of the base.
ferent icons
The handset is not
flash in the
registered.
display.
The base is not
switched on.
Cords not routed
correctly
Service (Customer Care)
We offer you support that is fast and tailored to
your specific needs!
Our Online Support on the Internet:
www.siemens-mobile.com/gigasetcustomercare
For more information on aftersales service, please
refer to your local warranty card.
In some countries repair and replace services are
impossible where the products are not sold
through our authorised dealers.
!
Solution
Press the end call
a
key
for approx.
5 seconds or place
the handset in the
base.
Charge/replace the
battery pack (page 2).
R
Press the hash key
for approx. 2 sec
(page 3).
Move the handset
closer to the base.
Register the handset
(page 5).
Check the power con-
nector at the base
(page 2).
Check cord routing
(page 2).

Advertisement

loading