Install The Door Control - Craftsman 139.18054 Owner's Manual

WARNING
INSTALLATION STEP 6
CAUTION

Install the Door Control

Locate door control within sight of door, at a minimum
height of 5 feet (1.5 m) where small children cannot
reach, away from moving parts of door and door
hardware. If installing into drywall, drill 5/32" holes and
use the anchors provided. For pre-wired installations
(as in new home construction), it may be mounted to a
single gang box (Figure 2).
1. Strip 1/4" (6 mm) of insulation from one end of the
bell wire and connect it to the two screw terminals on
the back of the door control: white to 2, and white/red
to 1.
2. Door Control Button: Fasten securely with
6AB x 1-1/2" screws.
Console Model: Pry off cover along one side with a
screwdriver blade (Figure 1). Fasten with
6AB x 1-1/4" self-tapping screws (standard
installation) or 6-32 x 1" machine screws (pre-wired
installation) as follows:
• Install bottom screw, allowing 1/8" (3 mm) to
protrude above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid
cracking plastic housing. Do not overtighten.
• Insert top tabs and snap on cover.
3. (For standard installation only) Run bell wire up
wall and across ceiling to motor unit. Use insulated
staples to secure wire in several places. Do not
pierce wire with a staple, creating a short or open
circuit.
4. Connect the bell wire to the terminal screws on the
opener panel: white to 2; white/red to 1.
5. Position the antenna wire as shown.
6. Use tacks or staples to permanently attach
entrapment warning label to wall near door control,
and manual release/safety reverse test label in a
prominent location on inside of garage door.
NOTE: DO NOT connect power and operate opener at
this time. The trolley will travel to the full open position
but will not return to the close position until the sensor
beam is connected and properly aligned.
Lighted
Push Button
DOOR
CONTROL
BUTTON
STANDARD CONTROL CONSOLE
2-Conductor Bell Wire
Opener
Terminal Screws
1
BACK PANEL
18
WARNING
WARNING
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is not connected BEFORE installing door
control.
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a
closing garage door:
• Install door control within sight of garage door, out of
reach of children at a minimum height of 5 feet (1.5 m),
and away from all moving parts of door.
• NEVER permit children to operate or play with door control
push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed.
NEVER permit anyone to cross path of closing garage door.
6AB x 1-1/2" Screw
Door Control Button
6AB x 1-1/4" Screw
Control Console (std installation)
6-32 x 1" Screw
Control Console (pre-wired)
Figure 1
REMOVE & REPLACE COVER
To Replace,
To Remove,
Insert
Twist
Top Tabs
Here
First
2 3
9 9
1 1
7 7
3 3
5 5
KG KG
Antenna
HARDWARE SHOWN
ACTUAL SIZE
Insulated
Staples
Dry Wall Anchors
Figure 2
PRE-WIRED
INSTALLATION
24 Volt
2-Conductor
Bell Wire
DOOR CONTROL
BUTTON (BACK)
Bell
Wire
Terminal Screws
STANDARD CONTROL
(BACK VIEW)
Top
Mounting
Hole
RED
WHITE
Terminal
2 1
Screws
Bottom
Mounting
Bell
Hole
Wire