Sony BVM-L230 Operation Manual page 46

Menu
HD
SD
DC 2048 × 1080
DVI Computer
H Shift Offset
Channel Name
NTSC Setup Level
Component Level
Betacam Setup Level
RGB Range
1080I/PsF
46
Input Configuration Menu
Function and operation ([
Transmission matrix
ITU709: Matrix of ITU-R BT.709 standards
ITU601: Matrix of ITU-R BT.601 standards
SMPTE240M: Matrix of SMPTE-240M standards
Note
The internal fixed value applies to the transmission matrix of the RGB format or XYZ format.
Transmission gamma
2.2: Transmission gamma 2.2
2.6: Transmission gamma 2.6
RGB Full Range: Transmission gamma available when the Full Range signal in
quantization is input
S-LOG Standard: Log gamma available with the F23 Digital Cinematography Camera.
Select to run the 100% output level of the F23 with the 100% level of the monitor for
confirmation.
S-LOG Full: Log gamma available with the F23.
Select to fit the full dynamic range of the F23 in the 100% level of the monitor for
confirmation.
Note
As 2.6 (transmission gamma 2.6) is the setting for the XYZ format, the signal is not displayed
correctly except for the XYZ format input.
Sets the color profile of the HD signal.
You can select from [ITU-R BT.709], ITU-R BT.601, SMPTE 240M, D-Cine or User1 to
User5.
Sets the color profile of the SD signal.
You can select from ITU-R BT.709, [ITU-R BT.601], SMPTE 240M, D-Cine or User1 to
User5.
Sets the color profile of the digital cinema signal (2048 x 1080).
You can select from ITU-R BT.709, ITU-R BT.601, SMPTE 240M, [D-Cine] or User1 to
User5.
Sets the color profile of the DVI Computer signal.
You can select from [ITU-R BT.709], ITU-R BT.601, SMPTE 240M, D-Cine or User1 to
User5.
Sets the horizontal picture position when the analog signal is input.
You can select when Format is set to Composite Auto, Composite NTSC, Composite PAL,
Composite PAL-M, Composite SECAM, YC Auto, YC NTSC, YC PAL, YC PAL-M, YC
SECAM, Component YPbPr or Component RGB.
Set to –100 to +100*. [000]
*When the setting value is out of range, the display of the setting value is changed but the
horizontal position of the picture is not changed.
Not available in software version 1.1 or earlier.
Sets the NTSC setup level.
You can select when Format is set to Composite Auto, Composite NTSC, YC Auto or YC
NTSC.
You can select from 0% or 7.5%.
Sets the component level of the analog component 480/60i signal.
You can select when Format is set to Component YPbPr.
You can select from SMPTE/EBU-N10 or Betacam.
Sets the Betacam setup level when Component Level is set to Betacam.
You can select from 0% or 7.5%.
Not available in software version 1.1 or earlier.
When the 1080i/PsF signal is input, select the display mode.
You can select when Format is set to HD-SDI/D1 Auto, 4:2:2 YPbPr 10bit, 4:4:4 YPbPr 10bit,
4:4:4 RGB 10bit, 4:4:4 YPbPr 12bit, 4:4:4 RGB 12bit, 4:4:4 XYZ 12bit, Component YPbPr or
Component RGB.
When 1080I is selected, the I/P conversion signal is displayed. When 1080PsF is selected,
the progressive conversion (PsF to P) signal is displayed.
When the 1080PsF signal is input and 1080I is selected, the display delay is shortened. The
signal converted from PsF to P is not displayed and the I/P conversion signal is displayed.
]: factory setting)