How do I program my One for All URC-7110 remote control?

You can program your remote control using two methods: Direct Code Set Up or Search Method. Direct Code Set Up:Find the code for your device in the Code list (pages 50-57). Codes are listed by device type and brand name, with the most popular code listed first. Ensure your device is switched on (not on standby).Press and hold magic for 3 seconds until the blue LED stays on.Enter the 1st code listed for your device type and brand (e.g., TV Hitachi = 1576). The blue LED will blink twice and then switch off.Press POWER.If your device does NOT switch off, repeat steps 1-3 trying the next code listed for your brand. If still not successful, try the Search Method.Search Method: Switch on your television (not on standby) and aim your One For All remote at your TV. Press and hold MAGIC for 3 seconds until the blue LED stays on. Select the corresponding device (e.g., TV). Press 9 9 1. The blue LED will blink twice. Next, press POWER. Press CH+ (over and over) again until your device switches OFF. This may require pressing the key many times (up to 150 times). As soon as your television turns off, press the magic key to store the code. After either method, you should be able to switch your device back ON and control it successfully.

Where can I find the device codes for my One for All URC-7110 remote control?

The device codes are found in the Code list on pages 50-57 of the manual.

How do I set up my One for All URC-7110 remote control?

You can set up your remote control using two methods: Direct Code Set Up or Search Method. Direct Code Set Up:Find the code for your device in the Code list (pages 50-57). Codes are listed by device type and brand name, with the most popular code listed first. Ensure your device is switched on (not on standby).Press and hold magic for 3 seconds until the blue LED stays on.Enter the 1st code listed for your device type and brand (e.g., TV Hitachi = 1576). The blue LED will blink twice and then switch off.Press POWER.If your device does NOT switch off, repeat steps 1-3 trying the next code listed for your brand. If still not successful, try the Search Method.Search Method: Switch on your television (not on standby) and aim your One For All remote at your TV. Press and hold MAGIC for 3 seconds until the blue LED stays on. Select the corresponding device (e.g., TV). Press 9 9 1. The blue LED will blink twice. Next, press POWER. Press CH+ (over and over) again until your device switches OFF. This may require pressing the key many times (up to 150 times). As soon as your television turns off, press the magic key to store the code. After either method, you should be able to switch your device back ON and control it successfully.

What troubleshooting steps should I take if the setup codes for my URC-7110 remote don't work?

If your device does NOT switch off after trying a code during the Direct Code Set Up, you should repeat steps 1-3 trying the next code listed for your brand. If still not successful, try the Search Method. For more information, see pages 9 and 10 of the manual.

How do I connect my One for All URC-7110 remote control to my TV?

You can connect your remote control to your TV using two methods: Direct Code Set Up or Search Method. Direct Code Set Up:Find the code for your TV in the Code list (pages 50-57). Codes are listed by device type and brand name, with the most popular code listed first. Ensure your TV is switched on (not on standby).Press and hold magic for 3 seconds until the blue LED stays on.Enter the 1st code listed for your TV brand (e.g., TV Hitachi = 1576). The blue LED will blink twice and then switch off.Press POWER.If your TV does NOT switch off, repeat steps 1-3 trying the next code listed for your brand. If still not successful, try the Search Method.Search Method: Switch on your television (not on standby) and aim your One For All remote at your TV. Press and hold MAGIC for 3 seconds until the blue LED stays on. Select the TV device mode. Press 9 9 1. The blue LED will blink twice. Next, press POWER. Press CH+ (over and over) again until your TV switches OFF. This may require pressing the key many times (up to 150 times). As soon as your television turns off, press the magic key to store the code. After either method, you should be able to switch your TV back ON and control it successfully.

What should I do if my One for All URC-7110 remote control is not responding?

If, during the Direct Code Set Up, your device does NOT switch off after entering a code and pressing POWER, you should repeat steps 1-3 trying the next code listed for your brand. If still not successful, try the Search Method. Additionally, if the LED becomes dim, you should replace the batteries. For more information, see pages 9, 10 and 65 of the manual.

Which devices are compatible with the One for All URC-7110 universal remote?

The One for All URC-7110 remote is compatible with Television / HDTV / LCD / Plasma / Projector / Rear Projector.

How do I reset my One for All URC-7110 remote control?

To perform an Operational Reset, which erases all learned functions across all modes and some other programmed functions like Key Magic and Macros:Press and hold magic for 3 seconds until a mode indicator (Blue LED) stays lit.Press 9 8 0. The blue LED will blink twice. For more information, see page 70 of the manual.

What do the blinking lights or indicators on the One for All URC-7110 remote signify?

The blue LED on the remote indicates various states during programming and operation:When pressing and holding magic for 3 seconds, the blue LED stays on to indicate it's ready for code input or programming.During Direct Code Set Up or Search Method, after entering a code or pressing 991, the blue LED will blink twice and then switch off, indicating successful input or completion of a step.During Key Magic® programming, after entering the function code and pressing the target key, the blue LED will blink twice, indicating the function has been assigned.During Macro programming, after pressing 995, the blue LED blinks twice. After entering the command sequence and pressing and holding magic, the blue LED blinks twice and switches off, indicating macro setup is complete.For Operational Reset, after pressing 980, the blue LED will blink twice, indicating the reset is complete.When determining the Set Up Code (What is my "Set Up Code" again?), the blue LED blinks to represent the digits of the code (number of blinks corresponds to the digit, zero blinks for '0').If the LED becomes dim, it signifies that the batteries need to be replaced.

Does the One for All URC-7110 remote control support a learning function from another remote?

Yes, the remote supports a learning function called "Key Magic®". This feature allows you to program functions from your original remote control, even if it is lost or broken. You can obtain 5-digit function codes from customer service and then program them to a key of your choice on the One for All remote. To program a function using Key Magic®:Press and hold magic for 3 seconds until a mode indicator (Blue LED) stays lit.Press 9 9 4. The blue LED will blink twice.Press and release the magic key.Enter the 5-digit function code provided by Customer Service.Press the key to which the function will be assigned (e.g., red key). The blue LED will blink twice.To reset a key to obtain its original function: Select the corresponding device mode (e.g., TV). Press and hold magic for 3 seconds until a mode indicator (Blue LED) stays lit. Press 9 9 4. Press the corresponding key (e.g., red) twice.

Can I program custom macro commands on the One for All URC-7110 remote?

Yes, you can program macro commands. A macro allows you to send a sequence of commands with the press of a single key. To set up a macro (e.g., to switch ON your TV and go directly to EXT 2 for your Playstation):Press and hold magic for 3 seconds until a mode indicator (Blue LED) stays lit.Press 9 9 5. The blue LED will blink twice.Press the key to which the function will be assigned (e.g., the -/-- key).Enter the sequence of commands, pressing each key once (e.g., POWER, then AV twice).Press and hold magic for 3 seconds until the blue LED blinks twice and then switches off.To reset a macro key to obtain its original function: Press and hold magic for 3 seconds until a mode indicator (Blue LED) stays lit. Press 9 9 5. Press the corresponding macro key (e.g., the -/-- key). Press and hold magic key for 3 seconds until the blue LED blinks twice.