Summary of Contents for MTD Pro F5, F8
- Page 1 ® Operator’s Manual & Illustrated Parts Walk-Behind Blower Landscape Maintenance Products Models MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A.
-
Page 2: Safety Precautions
Note: Safety goggles and long pants should be worn when operating or maintaining this machine. This manual presents the safety, operating instructions and parts breakdowns to keep your Walk-Behind Blower at peak efficiency. If properly operated and maintained, your Walk-Behind Blower will give dependable service. -
Page 3: Engine Maintenance
3. Clean the air filter paper element by gently tapping o the flat side. Do not wash or use pressurized air. 4. Position the blower o a level surface and check the engine oil level. 5. Fill the gas tank. - Page 4 5HP Handle Assembly - Figure 1 Note: Use No. 00050539 General Purpose Gun Grease.
- Page 5 00030488 Wheel Spacer 01001414 Brace 01001418 Frame Assembly Note: Determine which Blower you have purchased from the list below. Walk-Behind Blower Model No. F5 with 5-H.P. Briggs & Stratton Engine. Walk-Behind Blower Model No. F8 with 8-H.P. Briggs & Stratton Engine.
- Page 6 8HP Handle Assembly - Figure 2...
- Page 7 8HP Handle Assembly - Parts List for Figure 2 Ref. No. Part No. 00006129 HHCS, 5/16-18, 1-3/4 00011075 Flat Washer, 5/16 USS 00012169 Flat Washer, SAE 5/16 00012199 Nut, 5/8-18, Nylock Thin 00012382 HHCS, Standard, 5/16-18 x 1-1/2 00012470 Cable Tie, 3/16 x .05 x 7.4 00013406 HHCS, Standard, 5/16-18 x 3/4 00030906 Machine Screw, 10-32 x 5/8 00014608 Nylon, Lock Nut, 10-32...
- Page 8 5HP Engine and Blower Assembly - Figure 3...
- Page 9 5HP Engine and Blower Assembly - Parts List For Figure 3 Ref. No. Part No. 00006129 HHCS, 5/16-18, 1-3/4 00010022 Key, Stock, 1/4 x 1 -1/8 00012134 HHCS, Standard, 1/4-20 x 3/4 00012168 Lock Washer, 5/16 00012169 Flat Washer 00012171 HHCS Standard, 5/16-18 x 3/4...
- Page 10 8HP Engine and Blower Assembly - Figure 3...
- Page 11 8HP Engine and Blower Assembly - Parts List For Figure 4 Ref. No. Part No. 00006129 HHCS, 5/16-18, 1-3/4 00010022 Key, Stock, 1/4 x 1 -1/8 00010980 HHCS, 3/8-16, 2.00 00012134 HHCS, Standard, 1/4-20 x 3/4 00012157 Lock Washer, 3/8...
- Page 12 What Is Covered By This Warranty. This limited warranty covers any defect in materials or workmanship in your MTD Pro equipment for one year from the date of purchase for the first user purchaser. MTD Pro will replace or repair any part or parts without charge through your authorized MTD Pro dealer.
Need help?
Do you have a question about the F5, F8 and is the answer not in the manual?
Questions and answers
MYD Pro extreme auger snowblower. How do I turn off the gas flow to winterize the unit?
To turn off the gas flow to winterize the MTD Pro extreme auger snowblower, shut off the fuel shutoff valve.
This answer is automatically generated