Table of Contents
Advertisement
Quick Links
S
M
L
IGN
AGNITUDE
I
:
NPUTS
RCA O
:
UTPUTS
O
I
:
UTPUT
MPEDANCE
B
O
:
ALANCED
UTPUT
V
C
:
OLUME
ONTROL
S
F
:
AMPLING
REQUENCY
D
F
:
IGITAL
ILTER
S
:
LEW RATE
S
T
:
ETTLING
IME
D
R
:
YNAMIC
ANGE
N
F
:
OISE
LOOR
THD+N:
S
N
R
:
IGNAL TO
OISE
ATIO
C
S
:
HANNEL
EPARATION
C
F
:
ONTROL
EATURES
DAC S
ADDER
PECIFICATIONS
C
, T
OAXIAL
OSLINK
AES/EBU, 2 MSB N
(192K)
AND A
A
I
NALOG
NPUT
3.6V RMS (10Vpp)
50
0dB
OHMS AT
7.5 V RMS (20Vpp)
2 dB
STEPPED ATTENUATOR
)
STEPS
1.5
H
5
H
M
Z UP TO
M
8
O
TIMES
VERSAMPLING
>1000 V/
MICROSECOND
<90
NANOSECONDS
136 dBA
MEASURED
< -145 dB
.002
140 dB
>130 dB
R
EMOTE
D
ISPLAY DIM MODE
P
I
HASE
NVERT
F
O
ILTER
PTION
U
PSAMPLING
V
OLUME AND INPUT SELECT
,
BALANCED
ETWORK
B
ALANCED
(32
Z
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MSB Technology DAC II
Summary of Contents for MSB Technology DAC II
- Page 1 DAC S AGNITUDE ADDER NPUTS AES/EBU, 2 MSB N (192K) RCA O 3.6V RMS (10Vpp) UTPUTS UTPUT MPEDANCE 7.5 V RMS (20Vpp) ALANCED UTPUT 2 dB OLUME ONTROL STEPS AMPLING REQUENCY IGITAL ILTER >1000 V/ LEW RATE <90 ETTLING 136 dBA YNAMIC ANGE <...
- Page 2 That means that an active preamp with many stages if perfect would have no effect and any imperfection would result in degradation of the music. That is why we have used a passive preamp within the DAC II, to achieve the simplest, shortest possible signal path, with the least possible degradation of the true music.
- Page 3 Volts/microsecond. The output impedance of the Platinum is 50 ohms. The DAC II has 4 control buttons on the front panel, a knob and a display. The buttons toggle on and off. When on, the LED next to the button is lit.
- Page 4 The same remote works with the Platinum CD player and the Platinum volume control. If using the DAC II with a Platinum volume control, remove the volume modules from the DAC II so they will not interfere with the operation of the Platinum volume control.
- Page 5 SACD player to your system. Minimum input impedance is 600 ohms. For an RCA input, use an RCA to XLR conversion connector. At 0 dB volume setting, the analog inputs are a direct pass-through. Toslink – Although this format has the lowest bandwidth, it is one of the more common outputs on low-end products. It also offers ground isolation between products and noise immunity over long runs.
- Page 6 Remove the cover of the Platinum. Work on a soft scratch resistant surface like a carpeted floor. Three screws are located along the back edge and three screws on the bottom along the front edge. With these screws out, the cover lifts off. Now the power supply must be separated from the DAC.
- Page 7 Custom tailored for DACs your system. User installable. Signature DAC and Volume Control Installed at Factory This signature series upgrade is available for both the DAC II and CD STATION II. Factory installed only.
Need help?
Do you have a question about the DAC II and is the answer not in the manual?
Questions and answers