Motorola T6500 Series User Manual

• Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure
to Radiofrequency Electromagnetic Fields in the Frequency Range
from 3 KHz to 300 GHz, 1999
• Australian communications Authority Radiocommunications
(Electromagnetic Radiation—Human Exposure) Standard, 2003
• ANATAL ANNEX to Resolution No. 303 of July 2, 2002 "Regulation of
limitation of exposure to electrical, magnetic and electromagnetic
fields in the radio frequency range between 9 KHz and 300GHz" and
"Attachment to resolution #303 from July 2, 2002"
To assure optimal radio performance and make sure human exposure
to radio frequency electromagnetic energy is within the guidelines set
forth in the above standards, always adhere to the following
procedures.
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could damage
the radio and may violate FCC regulations.
Do NOT hold the antenna when the radio is "IN USE." Holding the
antenna affects the effective range.
Body-Worn Operation
To maintain compliances with FCC/Health Canada RF exposure
guidelines, if you wear a radio on your body when transmitting, always
place the radio in a Motorola-supplied or approved clip, holder, holster,
case or body harness for this product. Use of non-Motorola-approved
accessories may exceed FCC/Health Canada RF exposure guidelines.
If you do not use one of the Motorola-supplied or approved body-worn
accessories and are not using the radio held in the normal use
T6500 Series
position, ensure the radio and its antenna are at least 1 inch (2.5 cm)
KEM-PK14190-01
User's Guide
from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or without
an accessory cable, position the radio and its antenna at least one
inch (2.5 cm) from the body.
Approved Accessories
For a list of approved Motorola accessories, visit out Web site at
www.Motorola.com.
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shielded, designed or otherwise
configured for electromagnetic compatibility. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts,
turn off your radio in any facility where posted notices instruct you to
do so. Hospitals or health care facilities may be using equipment that is
sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when onboard on aircraft.
Any use of a radio must be in accordance with applicable regulations
per airline crew instructions.
Medical Devices – Pacemakers
The Advanced Medical Technology Association recommends that a
For More Information
minimum separation of 6 inches (15 cm) be maintained between a
handheld wireless radio and a pacemaker. These recommendations are
For further information, you may call Motorola at 1-800-638-5119 (U.S.
consistent with the independent research by and recommendations of
and Canada) or visit us on the Internet at http://www.motorola.com.
the U.S. Food and Drug Administration.
People with pacemakers should:

Safety and General Information

• ALWAYS keep the radio more than 6 inches (15 cm) from their
pacemaker when the radio is turned ON.
Important Information on Safe and Efficient Operation
• Not carry the radio in the breast pocket.
Read This Information Before Using Your Radio.
• Use the ear opposite the pacemaker to minimize the potential for
The information provided in this document supersedes the general
interference.
safety information in user guides published prior to December 1, 2002.
• Turn the radio OFF immediately if there is any reason to suspect that
interference is taking place.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To control
Medical Devices – Hearing Aids
your exposure and ensure compliance with the general Some digital wireless radios may interfere with some hearing aids. In
population/uncontrolled environment exposure limits, always adhere to the event of such interference, you may want to consult your hearing
the following procedure: aid manufacturer to discuss alternatives.
Other Medical Devices
• Transmit no more than 50% of the time.
If you use any other personal medical device, consult the manufacturer
• To receive calls, release the PTT button.
of your device to determine if it is adequately shielded from RF energy.
• To transmit (talk), press the Push to Talk (PTT) button.
Your physician may be able to assist you in obtaining this information.
Transmitting 50% of the time, or less, is important because the radio
Safety and General Use While Driving
generates measurable RF energy exposure only when transmitting (in
Check the laws and regulations regarding the use of radios in the area
terms of measuring standards compliance). where you drive, and always obey them. If you do use your radio while
driving, please:
Exposure to Radio Frequency Energy
Your Motorola two-way radio complies with the
• Give full attention to driving and to the road.
following RF energy exposure standards and guidelines:
• Use hands-free operation, if available.
• United States Federal communications Commission, Code of Federal
• Pull off the road and park before making or answering a call if driving
Regulations; 47CFR part 2 sub-part J
conditions so require.
• American National Standards Institute (ANSI)/Institute of Electrical
Do not place a portable radio in the area over an air bag or in the air
and Electronic Engineers (IEEE) C95. 1-1992
bag deployment area. Air bags inflate with great force. If a portable
• Institute of Electrical and Electronics Engineers (IEEE) C95.1-1999
radio is placed in the air bag deployment area and the air bag inflates,
Edition
the radio may be propelled with great force and cause serious injury to
• International Commission on Non-Ionizing Radiation Protection
occupants of the vehicle.
(ICNIRP) 1998
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive
atmosphere. Only radio types that are especially qualified should be
used in such areas as "Intrinsically Safe." Do not remove, install or
charge batteries in such areas. Sparks in a potentially explosive
atmosphere can cause an explosion or fire resulting in bodily injury or
Use to:
even death.
• Turn radio on/off.
Note: The areas with potentially explosive atmospheres referred to
• Increase or
above include fueling areas such as below decks on boats, fuel or
decrease volume
chemical transfer or storage facilities, areas where the air contains
chemicals or particles (such as grain, dust or metal powders) and any
other area where you would normally be advised to turn off your vehicle LED Indicator Light
engine. Areas with potentially explosive atmospheres are often—but not
always—posted.
Use Push to Talk
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your to:
PTT
radio when you are near electrical blasting caps, in a blasting area, or in
• Talk
areas posted "Turn off two-way radios." Obey all signs and instructions.
• Save a setting
Operational Cautions
Antennas
Use to:
Do not use any portable radio that has a damaged antenna. If a damaged
• Transmit call tone
antenna comes into contact with your skin, a minor burn can result.
Use – and
Batteries
to:
All batteries can cause property damage and/or bodily injury such as
• Scroll through menus
burns if a conductive material—like jewelry, keys or beaded chains—
• Turns weather
touch exposed terminals. The conductive material may complete an
on/off (+)
electrical circuit (short circuit) and become quite hot. Exercise care in
handling any charged battery, particularly when placing it inside a
pocket, purse or other container with metal objects.
Battery Charger Safety Instructions:
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a sharp
blow, or has been dropped or damaged in any way.
3. Never alter the AC cord or plug provided with the unit. If the plug will
not fit the outlet, have the proper outlet installed by a qualified
Numbers for
electrician. An improper condition can result in a risk of electric
Channel,
shock.
Call Tone
4. To reduce the risk of damage to the cord or plug, pull the plug rather
than the cord when disconnecting the charger from the AC receptacle.
5. To reduce the risk of electric shock, unplug the charger from the outlet
before attempting any maintenance or cleaning.
6. Use of an attachment not recommended or sold by Motorola may
result in a risk of fire, electric shock or personal injury.
7. Make sure the cord is located so it will not be stepped on, tripped over – Battery Meter
or subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary.
– Channel Indicator
Use of an improper extension cord could result in a risk of a fire
and/or electric shock. If an extension cord must be used, make sure
that: – Lock
• The pins on the plug of the extension cord are the same number, size
– Scan
and shape as those on the plug of the charger.
• The extension cord is properly wired and in good electrical condition.
– Weather Alert
• The cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for
lengths up to 150 feet.
9. The supply cord of this charger cannot be replaced. If the cord is
damaged, call Motorola Product Services at 1-800-353-2729 in the USA
or 1-888-390-6456 TTY (text telephone).

FCC Licensing Information

Installing the Batteries:
Your Motorola radio operates on General Mobile Radio Service (GMRS)
Your radio uses three AA Alkaline batteries and beeps when the
frequencies and is subject to the Rules and Regulations of the Federal
batteries are low.
Communications Commission (FCC). The FCC requires that all operators
1. Turn the radio off.
using GMRS frequencies obtain a radio license before operating their
2. With the back of the radio facing you, lift the battery latch up to
equipment. To obtain the FCC forms, please request Form 605 and 159,
release the battery cover and remove the cover.
which includes all of the forms and instructions you will need.
3. Insert three AA Alkaline batteries as shown on the inside of the
If you wish to have the document faxed or mailed, or if you have
battery compartment.
questions, please use the following contact information:
4. Reposition the battery cover and press down to secure.
NOTE: The T6500 series models can use a NiMH rechargeable battery
For a Fax: For Mail Service: If You Have Questions
pack instead of three AA Alkaline batteries.
Contact the Fax-On Call the FCC Forms about the FCC License:
Demand system Hotline Call the FCC
1-202-418-0177 1-800-418-FORM (3676) 1-888-CALL-FCC
Installing the NiMH Battery Pack:
(225-5322)
1. Follow step 2 above to remove the battery cover.
2. Remove the battery pack from the clear plastic bag. Do not
You may also visit the FCC's Web site at http://www.fcc.gov. disassemble or unwrap the battery pack.
3. Insert the NiMH battery pack so the "This Side Up" is showing.
Changes or modifications not expressly approved by Motorola may void
4. Reposition the battery cover and press down to secure.
the user's authority granted by the FCC to operate this radio and should
not be made. To comply with FCC requirements, transmitter adjustments
Battery Meter
should be made only by or under the supervision of a person certified as
The battery icon shows the battery charge level, from full
technically qualified to perform transmitter maintenance and repairs in
to empty
the provide land mobile and fixed services as certified by an organization
after releasing
representative of the user of those services. Replacement of any
voltage drops below a predetermined level to protect the rechargeable
transmitter component (crystal, semiconductor, etc.) not authorized by
battery.
the FCC equipment authorization for this radio could violate FCC rules.
Note: Remove the batteries before storing your radio for extended
Note: Use of this radio outside the country where it was intended to be
periods of time. Batteries corrode over time and may cause permanent
distributed is subject to government regulations and may be prohibited.
damage to your radio.
Using the Desk Stand Charger (Optional Accessory)

Control Buttons

The desk stand charger provides drop-in charging convenience for
NiMH batteries and can be placed on any flat surface, such as a desk
or workbench. Charge the NiMH battery overnight (at least 16 hours)
before using it for the first time. After the initial charge, an empty
battery is fully charged within 14 hours.
Use to:
MENU
1. Follow the steps above to install a NiMH Battery Pack.
• Select Menu options
2. Plug the AC power supply into the plug on the desk stand.
• Exit the Menu
3. Plug the AC power supply into a standard wall outlet.
(when pressed
4. Remove the battery pocket inserts from the charger pockets.
while in a Menu)
5. With a radio facing forward, slide it into one of the charging pockets.
• Lock and unlock
Notes
the keypad (when
• The light on the charging base will glow continuously when
held down and
radio/battery is inserted.
not in a Menu)
• When moving between hot and cold temperatures, do not charge the
Accessory Jack
battery until the battery temperature acclimates (usually about 20
minutes).
Use to:
MON
• For optimal battery life, remove the radio or battery from the charger
• Monitor channel activity
within 16 hours. Do not store the radio in the charger.
• Scan to see if anyone is
• Turn radio off while in charging tray.
on the selected
channel
Attaching and Removing the belt clip
+
Microphone 1. Align the belt clip post with the hole in the back of the radio.
2. Gently push until the clip clicks in place
Speaker
To Remove
1. Push down on the release tab at the top of the belt clip to release
the catch.
2. Pull the belt clip away from the back of the radio.
Turning Your Radio On and Off
Display Screen Guide Turn clockwise to turn the radio on and counterclockwise to turn
the radio off.
1. The radio chirps and briefly shows all features icons available on
your radio.
2. The display then shows the current channel, code and features that
are selected.
Setting the Volume
Numbers for
Press and hold while rotating
Codes
MON
listening level.
1. Rotate clockwise to increase the volume.
2. Rotate counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
– Talk Confirmation Tone

Talking and Listening

(Roger Beep)
To communicate, all radios in your group must be set to the same
– Noise Filtering
channel and Interference Eliminator Code.
– Hands-Free Use
1. To talk, press and hold
Without
2. When you are finished talking, release
Accessories
For maximum clarity, hold the radio two to three inches away from your
– Vibrate
mouth and speak directly into the microphone. Do not cover the
microphone while talking.
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet apart.
Monitor Button

Getting Started

Pressing and holding MON
volume level of the radio when you are not receiving. This allows you
to adjust the volume, if necessary. You can also use
activity on the current channel before you talk.
Push to Talk PTT Timeout Timer
To prevent accidental transmissions and save battery life, the radio
emits a continuous warning tone and stops transmitting if you press
PTT for 60 continuous seconds.
Selecting a Channel
Your radio has 22 channels. Channels 8-14 are FRS 0.5 watt only and all
other channels are 1 watt GMRS. When the radio is on a 0.5 watt
channel, displays. When the radio is on a 1 watt channel,
displays.
1. With the radio on, press
+
–
2. Press or to select a channel.
3. Press PTT to confirm your selection or
. When the battery is empty, the radio chirps periodically
PTT (Low Battery Alert). The radio powers off when the
Channels and Frequencies
Channel Frequency Description Channel Frequency Description
1 462.5625 GMRS/FRS
MHz
2 462.5875 GMRS/FRS
MHz
3 462.6125 GMRS/FRS
MHz
4 462.6375 GMRS/FRS
MHz
5 462.6625 GMRS/FRS
MHz
6 462.6875 GMRS/FRS
MHz
7 462.7125 GMRS/FRS
MHz
8 467.5625 FRS
MHz
9 467.5875 FRS
MHz
10 467.6125 FRS
MHz
11 467.6375 FRS
MHz
Interference Eliminator Code
Interference Eliminator Codes help minimize interference by providing
you with a choice of code combinations. Your radio has 121
Interference Eliminator Codes. Codes 1 - 38 are the standard codes that
appear on other FRS/GMRS radios. Codes 39 - 121 are additional codes
added for superior interference protection.
1. Short press MENU until the code starts to flash.
2. Press or to select the code.
+ –
until you reach a comfortable
3. Press to save the code setting or
PTT
You can set a different code for each channel using this procedure. An
extended press of + or allows you to scroll through the
–
Interference Codes rapidly so you can quickly reach the code you
want.
Note: You must set the Interference Eliminator Code to 0 on a radio that
uses Interference Eliminator Codes to communicate with radios that do
not have Interference Eliminator Codes.
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your group
so you can alert them that you want to talk. You have 10 call tones from
which to choose.
PTT .
To set a call tone:
PTT
.
1. With the radio on, short press MENU
flashes and CA appears.
2. Press + or – to change and hear the call tone.
3. Press to set the new call tone or
PTT
To transmit your call tone to other radios set to the same channel and
Interference Eliminator Code as your radio, press
Note: Setting the call to 0 disables the call tone feature.
VibraCall® Alert
VibraCall is a vibrating alert that notifies you that your radio is receiving
for three seconds allows you to listen to the
a message. This is useful in noisy environments. When the alert is on,
the radio vibrates once every 30 seconds when you receive a message
to check for
on the channel and code you set.
MON
1. To turn vibrating alerts on, press
MENU
current setting will flash.
2. Press or to change the setting to
+ –
3. Press to set or MENU to continue set up.
PTT
Setting the Sensitivity Level When in VOX or iVOX Mode
Initial Setup
Adjusting the radio's sensitivity level helps minimize the possibility of
unintended noises triggering a transmission and helps the radio pick up
soft voices.
1. Short press until . appears.
MENU
2. Press + or – to select the sensitivity level.
3. Press to set or MENU to continue set up.
PTT
. The current channel flashes.
MENU
3 = High Sensitivity for quiet environments
2 = Medium Sensitivity for most environments
MENU to continue set up.
1 = Low Sensitivity for noisy environments
Note: When you connect a VOX accessory, the radio is automatically
set to the last chosen sensitivity level.
See Special Features section on Accessories.
12 467.6625 FRS
MHz
13 467.6875 FRS
MHz
14 467.7125 FRS
MHz
15 462.5500 GMRS
MHz
16 462.5750 GMRS
MHz
17 462.6000 GMRS
MHz
18 462.6250 GMRS
MHz
19 462.6500 GMRS
MHz
20 462.6750 GMRS
MHz
21 462.7000 GMRS
MHz
22 462.7250 GMRS
MHz
to continue set up.
MENU
until the current call tone setting
to continue set up.
MENU
.
until is displayed. The
and – .
Continued on back
T6500