Agc Setting - Hitachi KP-D5000 Operation Manual

5) Move the cursor to PK/AV and push Set button to
display the ratio of peak and average.
Set button : 0/100→ 15/ 85→ 30/ 70→ 50/ 50
→ 75/ 25→ 100/0
The response to spot light increases with increment
in peak value. Factory setting is 15/85.

AGC setting

AGC mode setting
1) Press the Set button for longer than 2 seconds to display the
Main menu.
2) Use the Up and Down buttons to move the cursor to AGC.
AGC setting data blinks.
3) In this state, push the Set button to display AGC MENU.
◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆
ＡＧＣ ＡＧＣ ＡＧＣ ＡＧＣ ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ
> > > >
ＭＯＤＥ ＭＯＤＥ ：ＯＮ ：ＯＮ
ＭＯＤＥ ＭＯＤＥ ：ＯＮ ：ＯＮ
ＡＧＣ ＡＧＣ ＬＩＭＩＴ ＬＩＭＩＴ ：＋３１ ：＋ ３１
ＡＧＣ ＡＧＣ ＬＩＭＩＴ ＬＩＭＩＴ ：＋ ：＋ ３１ ３１
０ ０ ０ ０ ・・・・・・・・ ・・・・・・・・● ● ● ● ・・・・・・ ・・・・・・５１ ５１
・・・・・・・・ ・・・・・・・・ ・・・・・・ ・・・・・・ ５１
DNR DNR DNR DNR ： ： ： ： OFF OFF OFF OFF
ＲＥＴ ＲＥＴ
ＲＥＴ ＲＥＴ
ＥＮＤ ＥＮＤ ＥＮＤ ＥＮＤ
AGC setting menu (ON)
4) When the cursor is at MODE, push the Set button to change
the AGC modes as follows.
Set button : ON→OFF
ON : Automatically changes the video level within
a range of the AGC limit as appropriate according to
the brightness of subject. AGC is set to ON in
factory setting.
OFF : Always sets a fixed video level from the [FIX. GAIN].
......AGC mode display
......AGC lmit (0~+51)
......AGC limit gauge
５１
......Digital Noise Reduction（DNR）display
......Return to Main menu
......End (Menu display off）
AIE mode
AIE is a function to correct brightness of the part that has
darkened as a result of over exposure control by BLC and
PEAK/AVE.
When the cursor is at AIE, push the Set button to change the
AIE modes as follows.
Set button : OFF→LOW→MID→HIGH
OFF : AIE is inactive.
It is set for AIE in factory setting.
LOW, MID, HIGH : AIE is effective.
The enhancement level of the part that
has darkened is changed to
LOW, MID, HIGH.
Note
The part that has darkened is corrected brightness by
the enhancement level increment, but the picture might
be noisy. Therefore, set the enhance level with taking
picture conditions.
21
AGC limit setting (AGC ON)
1) When the cursor is at AGC LIMIT, push the Set button.
A mark[●] at the AGC limit gauge flashes.
2) In this state, use the Up and Down buttons to change
the AGC limit.( 0～+51). For factory setting by the Scene file
(page 17), hold down both the Up and Down buttons
simultaneously for 2 seconds.
3) In this state, pressing Set button will stop blinking and setting
value will be fixed. The the cursor moves to RET.
AGC limit setting (AGC OFF)
◆ ◆ ◆ ◆
ＡＧＣ ＡＧＣ ＡＧＣ ＡＧＣ ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ
> > > >
ＭＯＤＥ ＭＯＤＥ ：Ｏ ：ＯFF FF
ＭＯＤＥ ＭＯＤＥ ：Ｏ ：Ｏ FF FF
ＦＩＸ ＦＩＸ ＧＡＩＮ ＧＡＩＮ ：＋３１ ：＋ ３１
ＦＩＸ ＦＩＸ ＧＡＩＮ ＧＡＩＮ ：＋ ：＋ ３１ ３１
－ － － － ６ ６ ６ ６ ・・・・・・・・ ・・・・・・・・ ・・・・・・・・● ● ● ● ・・・・・・ ・・・・・・・・ ・・・・・・ ・・・・・・ ・・・・・・５１
DNR DNR DNR DNR ： ： ： ： OFF OFF OFF OFF
ＲＥＴ ＲＥＴ
ＲＥＴ ＲＥＴ
Ｅ Ｅ Ｅ Ｅ ＮＤ ＮＤ ＮＤ ＮＤ
<<<
ＭＡＩＮ ＭＥＮＵ
ＴＩＴＬＥ ：ＯＦＦ
ＬＩＧＨＴ ＣＯＮＴＲＯＬ：ＯＦＦ
AGC setting menu (OFF)
>
ＡＧＣ ：ＯＮ（３１ｄＢ）
ＳＨＵＴＴＥＲ ＳＰＥＥＤ：ＯＦＦ
ＳＥＮＳ ＵＰ ：ＯＦＦ
Ｂ／Ｗ ＭＯＤＥ ：ＡＵＴＯ （ＭＩＤ）
1) When the cursor is at FIX GAIN, push the Set button.
ＷＨＩＴＥ ＢＡＬＡＮＣＥ：ＡＴＷ
ＤＩＧＩＴＡＬ ＺＯＯＭ ：ＯＦＦ
A mark[●] at the FIX GAIN gauge flashes.
ＳＵＢ ＭＥＮＵ ↵
ＥＮＤ
22
◆ ◆ ◆ ◆
......AGC mode display
......AGC lmit (－6~+51)
......AGC limit gauge
５１ ５１ ５１
......Digital Noise Reduction（DNR）display
......Return to Main menu
......End (Menu display off）
>>>
↵
↵
↵
↵
メイン設定メニュー