Reassembly - Sunbeam T20B Service Manual

-
5
-
of the
Element Assembly;
the
Insulator
(4)
slides off of the Bus
Bar.
Now the Window
End Assembly, End
Top Plate,
and Guide Wires can be separated. Follow
the
same
procedure and precautions
in
removing
the
other
End Top
Plate
(3)
and Closed End
Element Assembly
(6),
but first remove Hex Nut
(7)
and Washer
(8),
disconnecting Lower
Bus Bar from Center Element.
3.
Release Guide Wires, then remove Screws
(2).
Lift Center Element Assembly
(10),
with
Center Top
Plate attached, clear
of
the mechanism. Remove Screws
(18),
releasing
Lifter Lever Assembly
(19)
from mechanism, then remove Screws
(2)
freeing Frame Cross
Yoke
(15).
Remove Screws
(2),
and lift Side Frame
(14)
from Mounting Plate Assembly
and clear
of
Bread Lifter Assembly
(17).
Follow
the same
procedure for other
Side
Frame. Now you can pick
up
Bread Lifter Assembly off of Mounting Plate Assembly.
Unhook
Lift Lever
Depression Bar
(22)
from Lift Lever Assembly, separating Lift Lever
Depression Bar from the Mounting Plate Assembly.
B.
REASSEMBL
Y
1.
Set
Mounting Plate Assembly
(20)
on top of Lift Lever Depression Bar
(22)
and hook
Lift Lever
Assembly
(19)
onto Lift Lever Depression
Bar.
Connect Switch Lead
(21)
with
Washer
(8)
and Hex Nut
(7)
onto Mounting Plate Assembly. Place Bread Lifter Assembly
(17)
on top of Mounting Plate Assembly. Set Side Frame Assemblies
(14)
and
(16)
into
place with the Bread Lifter Assembly set in the slots and fasten with Screws
(2).
Now
with the Bread Lifter Assembly
set in slots of Side Frame Assemblies and Lift Lever
Assembly, fasten Frame Cross Yoke
(15)
with Screws
(2)
onto Side Frame Assembly.
2.
Set
Window End Element Assembly
(11)
and Closed End Element Assembly
(6)
into place.
Install Guide Wires
(9)
onto Center Top Plate of Center Element Assembly
(10).
Set
Center Assembly into place with Upper and Lower Bus Bars of the End Element Assemblies
on
respective terminals,
so
that Adjustment Screw
is in
center hole of Lift Lever
Depression
Bar,
and fasten Center Top Plate with Screws
(2).
Hook Guide Wires onto
Mounting Plate Assembly. Replace Washer
(8)
and Nut
(7)
on Bus Bar terminals of Center
Element. Slide Insulators
(4)
onto Bus Bar of Window End Element. Slide Thermostat
Assembly
(12)
into place, and connect
Upper Lead Bracket
of
Element Assembly and
Switch Lead Wire
(21)
onto Thermostat Assembly with Washers
(8)
and Screws
(13).
Hook
3
to
4
turns of Carriage Counter Balance Spring
(3A)
over Top End Plate
(3).
Hook
the
looped end
in
hole
in
Bread Lifter Assembly
(17).
Fasten End Shells
(5)
and Center
Shell
(1)
onto
mechanism assembly with Screws
(2)
.
Use Tool
No.
2
when
fastening
Center Shell
to
mechani
sm.
After End Shells are fastened, set Center Shell in place,
then holding Toaster by the
Base,
push down into Tool
No.
2
until holes
in
Center
Shell are lined up
with holes on Mounting Plate Assembly. Insert Screws and tighten.
Push Cord Clamp
(23)
into slot
in
Mounting Plate Assembly. Push terminal end of Plug
and Cord Assembly
(24)
through hole provided in Base
(25)
and