Cycle Guide - Kenmore 110.66132*410 Use & Care Manual

Damp Signal
Touch to select the Damp Signal to on or off. When
selected, a series of beeps will sound when the load is
damp, but not completely dry. This will allow you to take
clothes out of the load that do not need to dry completely.
This option is not available on Sanitize, Steam Refresh,
and the Timed cycles.
CYCLE STATUS LIGHTS
6
The indicator bar on the right side of the control will let you
know what stage of the drying cycle is in process.
Damp
This indicator shows that the load is partially dried and
items that you may wish to hang up or iron while still
damp may be removed.
Cool Down
The dryer has finished drying with heat, and is now
tumbling the load without heat to cool it down and
reduce wrinkling.
SENSING CYCLES –
Senses moisture in the load and shuts off when the load reaches the selected dryness level. The dry temperature
shown is the default temperature. This setting can be modified on some cycles but is not retained for future drying with this cycle. The
dryness level shown is the default dryness setting. This setting can be changed on some cycles and will be retained for future drying with
this cycle. Available options in bold are default settings for that cycle.
To get the most energy savings and enhanced fabric care from your dryer, use the Sensing cycles. These cycles measure the drying
air temperature and moisture levels to turn the dryer off once the load reaches the selected dryness level. For electric models, dryer
performance and results may vary with service voltage less than 240.
Items to dry: Cycle:
Towels and Sanitize*
bedding
Jackets, Bulky/
comforters, pillows Bedding
Heavyweight items Heavy
such as towels and Duty
jeans
Corduroys, work Normal
clothes
No-iron fabrics, Casual
cottons, perm
press, linens,
synthetics
Lingerie, blouses, Delicates
washable knit
fabrics
* Extended high-heat drying cycle intended to help sanitize items such as sheets and towels. This cycle is not recommended for all
fabrics. For best results, this cycle should be run to completion to ensure sanitization and do not interrupt cycle.
If loads do not seem as dry as you would like or are drier than you would like, select More Dry or
†
Less Dry next time you dry a similar load.
6
CYCLE GUIDE – SENSING CYCLES
Dry Temp: Dry Level
Complete
This will indicate that the selected cycle has ended and
the load may be removed from the dryer. If Wrinkle
Guard™ option has been selected, the dryer may continue
to tumble the load, even if the Complete indicator is lit.
Wrinkle Guard™
This indicator will light if the Wrinkle Guard™ option has
been selected and is running. The dryer will periodically
tumble the load for up to 150 minutes after the cycle has
ended.
Check Lint Screen
The Check Lint Screen indicator light will flash as a
reminder to clean the lint screen. It will flash until the door
is opened or a cycle is started. It will turn off when the
dryer is turned off.
START/PAUSE BUTTON
7
Touch and hold START/PAUSE button for up to 3 seconds or
until the dryer starts to begin the selected cycle; touch again
to pause a cycle.
: Available
†
Options:
Wrinkle Guard™
Cycle Signal
Damp Dry Signal
Wrinkle Guard™
Cycle Signal
Damp Dry Signal
Wrinkle Guard™
Cycle Signal
Damp Dry Signal
Wrinkle Guard™
Cycle Signal
Damp Dry Signal
Wrinkle Guard™
Cycle Signal
Damp Dry Signal
Wrinkle Guard™
Cycle Signal
Cycle Details:
Extended high-heat drying cycle
intended to help sanitize items such as
bedding and towels. This cycle is not
recommended for all fabrics. For best
results, run cycle to completion, do not
interrupt.
NOTE: Steam portion of Wrinkle
Guard™ w/Steam option is disabled for
this cycle.
Use for drying large, bulky items; do not
overfill dryer drum.
Use for drying large or heavy items.
Medium to large loads of mixed fabrics
and items.
For normal light- to medium-weight
fabrics. Drying time varies based on
fabric type, load size, and dryness
setting.
For gently drying delicate items.
NOTE: Steam portion of Wrinkle
Guard™ w/Steam option is disabled for
this cycle.