Specifications - Sharp XV-Z2000 Service Manual

Product type Projector
Model XV-Z2000, DT-400
Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480
Display method Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
DLP panel Panel size: 0.8"
Drive method: Digital Light Processing (DLP™)
No. of dots: 921,600 dots (1,280 [H] ⋅ 720 [V])
1–1.5 ⋅ zoom lens, F2.0–2.5 f=21.3–31.6 mm
Lens
Projection lamp 275 W DC lamp
RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω
Video input signal
terminated
S-video input signal 4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Component input signal RCA Connector
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
(INPUT 1, 2)
P
B
P
R
Analog RGB/Digital 29-pin DVI-I terminal
(INPUT 5/DIGITAL) <Digital>
Input impedance 50 Ω
Input level 250-1000 mV
<Analog>
Input impedance 75 Ω
Input level 0.7 Vp-p
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
P
B
P
R
<Synchronization signal>
• Separate sync/Composite sync
• Green on sync
Horizontal resolution 720 TV lines (DTV 720P input)
Pixel clock 12–80 MHz
Vertical frequency 43–75 Hz
Horizontal frequency 15–70 kHz
Computer control signal 9-pin D-sub connector (RS-232C Port)
Rated voltage AC 100–240 V
Input current 3.65 A (When using AC 100 V)
Rated frequency 50/60 Hz
Power consumption 360 W (When using AC 100 V)
Power consumption (standby) 6 W (When using AC 100 V)
Heat dissipation 1,350 BTU/hour
Operating temperature 41°F to 95°F (+5°C to +35°C)
Storage temperature –4°F to 140°F (–20°C to +60°C)
Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 12
Weight (approx.) 9.5 lbs. (4.3 kg)
Supplied accessories Remote control, Two AA size batteries, Power cord, Lens cap (attached on the body),
Operation manual
Replacement parts
Lamp unit (Lamp/cage module) (AN-K2LP), Remote control (RRMCGA334WJSA), AA
size batteries, Power cord (QACCBA036WJPZ:XV-Z2000, for U.K., Hong Kong and
Singapore), (QACCDA007WJPZ:XV-Z2000, for U.S.A., Canada and DT-400),
(QACCLA018WJPZ:XV-Z2000, for Australia and New Zealand),
(QACCVA011WJPZ:XV-Z2000, for Europe, except U.K.) Lens cap (PCAPHA021WJSA),
Operation manual (TINS-B529WJZZ:XV-Z2000, for U.S.A., and Canada),
(TINS-B530WJZZ:XV-Z2000, for European 7 Laguges),
(TINS-B531WJZZ:XV-Z2000, for Hong Kong and Korean), (TINS-B532WJZZ:DT-400)
Operation manual, for 21pin RCA Conversion Adaptor (TCADH1018CEN1:XV-Z2000,
for Europe) Video cable (QCNWGA001WJZZ:XV-Z2000, except U.S.A., Canada and
DT-400), 21pin RCA conversion adaptor (QSOCZ0361CEZZ:XV-Z2000, for Europe)
As a part of policy of continuous improvement, SHARP reserves the right to make design and
specification changes for product improvement without prior notice. The performance specifica-
tion figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.

SPECIFICATIONS

I /480P/540P/576 I /576P/720P/1080
): 0.7 Vp-p, 75 Ω terminated
(C
B
): 0.7 Vp-p, 75 Ω terminated
(C
R
): 0.7 Vp-p, 75 Ω terminated
(C
B
): 0.7 Vp-p, 75 Ω terminated
(C
R
Input level TTL level
Input impedance 1 KΩ
Input level (Synchronizing input) 0.286 Vp-p
Input impedance 75 Ω
" ⋅ 3 " ⋅ 11 " (310 (W) ⋅ 89 (H) ⋅ 282 (D) mm)
7 / 33 / 7 /
32 64 64
3
I
XV-Z2000
DT-400