Yamaha RX-V563 Owner's Manual page 72

SET MENU
• Speaker distance C) SP DI STi=ltK:E
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
• Center speaker equalizer D) CEtHER I3EG!
Use this feature to adjust the built-in 5-frequency band
(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments while listening to the currently
selected source component or a test tone.
Control range: -6.0 to +6.0 dB
Control step: 0.5 dB
Initial setting: 0 dB
1 SOUND t'IEflU 1 SOUND t1EflU
C)SP DISTRNCE
1/2
C)
SP DISTRt,CE
2/2
• UNIT········feet
• SUR. L···· ·8.0ft
FRONT L···10.0ft SUR. R···· ·8.0ft
FRONT R···10.0ft SB L·······8.0ft
CENTER·····8.5ft
SB R·······8.0ft
SWFR······10.0ft
[a]/(T]: Up/Down [a]/[T]:Up/Down
[ ... ]/[11-]:
~djust
["1]/(11-]:
~djust
1 SOUflD t'lENU
D)CENTER GEQ
TEST >OFF ON
• 100Hz ..
~~
..
300Hz··
~~
..
1kHz ..
~~
••
3kHz .•
~~
..
10kHz ..
~~
..
[a]/[T]:Up/Down
[<l]/[II-]:~djust
0dB
0dB
0dB
0dB
0dB
Unit
UtHT
Choices: meters (m), feet (ft)
Initial setting:
[U.S.A. and Canada models]: feet
(ft)
[Other models]: meters (m)
• Select "meters" to adjust speaker distances in meters.
• Select "feet" to adjust speaker distances in feet.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
Initial setting:
FRONT UFRONT R1SWFR: 3.00 m (10.0 ft)
CENTER: 2.60 m (8.5
ft)
SUR. L/SUR. R1SB USB R: 2.40 m (8.0
ft)
• The available speaker channels differ depending on the setting
of the speakers.
• Instead of "SB L" and "SB R", "SUR.B" is displayed if
"SUR.B UR SP" is set to either "SMLxl" or "LRGxl" (see
page 66).
FI<:otH L
FI<:ot-n R
CEtHER
51.JFR
SUR. L
5UI<:. R
58 L
58 R
Front left speaker
Front right speaker
Center speaker
Subwoofer
Surround left speaker
Surround right speaker
Surround back left speaker
Surround back right speaker
Test tone
TEST
Use this feature to make adjustments for "CENTER GEQ"
while listening to a test tone.
Choices: OFF, ON
• Select "OFF' to stop test tones and output the currently
selected source component.
• Select "ON" to output test tones from the center and
front left speakers.
• Low-frequency effect level E)LFE LEI.)EL
Use this feature to adjust the output level of the LFE (low-
frequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to'
certain scenes. This setting is effective when the input
signal contains the LFE channel.
Control range: -20 to 0 dB
Control step: 1 dB
1 SOUflD t1ENU
E)LFE LEVEL
•
SPE~KER······0dB
HE~DPHONE····0dB
Speaker
5PEi=lKER
Adjusts the speaker LFE level.
Headphone
HEi=lDPHOt·1E
Adjusts the headphone LFE level.
No!~J
Depending on the settings of "LFFlBASS OUT" (see page 66),
some signals may not be output at the SUBWOOFER OUTPUT
jack.
68
En