Related Manuals for Monitor Audio BRW-10
Summary of Contents for Monitor Audio BRW-10
-
Page 1: Table Of Contents
Amplifier Panel and Controls Positioning & Set Up Specification Guarantee and Service Claims under this guarantee EC Declaration of Conformity Data Protection Owner Information Warranty Card – Fold out section in back cover © Monitor Audio 2006 BRW-10 Rev4 Page... -
Page 2: Introduction
Introduction Thank you for your purchase of Monitor Audio Bronze BRW-10 subwoofer, which has been designed and constructed using quality systems and materials to provide years of enjoyment, reliability and pride of ownership. This product, as with all the Bronze BR range, is hand crafted from top to bottom using traditional woodworking skills for our sumptuous cabinets, married with the state of the art technology of our renowned drive units. -
Page 3: Safety Instructions
Any instructions preceded by this warning triangle MUST be followed. Failure to do so may cause personal injury or damage the unit/s. 4. Lifting/Moving Due to the weight of the BRW-10, care must be taken at all times when handling the product. 5. Power Unplug this apparatus during lightening storms or when unused for long periods of time. -
Page 4: Recycling (Weee)
You will fully appreciate that great care and attention has gone into the materials chosen to produce the Bronze BRW-10. It is our intention that it should provide a lifetime of musical pleasure. A gentle wipe with a dry, clean cloth is all that is required to remove any dust. -
Page 5: Foot Fixing
Foot Fixing The BRW-10 comes with rubber feet for fixing to the bottom of the cabinet. Also included are self taping screws to fix them to the bottom of the cabinet. These are very simple to attach, but please ensure care is taken at all times and the correct tools are used. -
Page 6: Amplifier Panel And Controls
Amp Panel and Controls © Monitor Audio 2006 BRW-10 Rev4... -
Page 7: Volume Control
The LED indicates whether the unit is in stand-by mode or operational. 2. RCA Line Level Inputs (Left & Right) This is the only method of signal input connection to the BRW-10. When using a stereo amplifier system, connection can be provided by a pair of high-quality signal cables from the pre-out section of an amplifier. - Page 8 It will remain on. If no signal is received for around 15-20 minutes, the BRW-10 will then switch into standby mode until a signal is received once more. With the switch in the ‘On’...
-
Page 9: Positioning & Set Up
Frequency control Phase control Power switch Input connections can be made at this stage before the power is connected to the BRW-10. Never connect or disconnect the RCA input lead connection with the BRW-10 switched on. Set Up Once the input cables are connected and the controls are set in accordance with the initial set-up procedure above, the BRW-10 can be connected to the mains power supply and switched on. -
Page 10: Specification
115 Vac / 230 Vac Factory Preset. Do not adjust Black Oak, Cherry and Walnut vinyl’s. All fitted with a black grille. © Monitor Audio 2006 BRW-10 Rev4 320 H x 320 W x 340 D x 12 x 13... -
Page 11: Guarantee And Service
The equipment should be returned in its original packaging to the original supplier where possible, or to any other authorised Monitor Audio dealer. If it is not possible to return the equipment by hand, then it should be sent carriage prepaid via a reputable carrier. -
Page 12: Ec Declaration Of Conformity
Unit 2,24 Brook Road Rayleigh Essex SS6 7XL England Declare in own responsibility, that the BRW-10 product described in this manual is in compliance with Technical Standards/Council Directives: (LVD) 73/23/EEC Low Voltage Directive EN60065 : 09.93+ A11:09.97 apparatus for household and similar use. -
Page 13: Data Protection
Data Protection We at Monitor Audio are committed to respecting the wishes and privacy of our customers. Any information you provide will be held in the strictest confidence and only used within the Monitor Audio organisation for the provision of services such as warranty claims or spare parts.