Download Table of Contents Print this page

Specifications; Additional Safety Rules; Operating Instructions - Makita HM1202 Instruction Manual

Hide thumbs Also See for HM1202:

Advertisement

Table of Contents
ENGLISH
1
Bit grease
2
Bit shank
3
Tool holder cover
4
Bit
5
Change ring
6
Side handle (auxiliary handle)
7
Can be swung 360° on the
vertical and secured at any
desired position
8
Secures at eight different
positions back and forth
on the horizontal

SPECIFICATIONS

Model
Blows per minute ......................................................................... 1,900
Overall length .............................................................................. 578 mm
Net weight ................................................................................... 9.3 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.46 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2.
Wear ear protectors when using the tool for
extended periods. Prolonged exposure to high
intensity noise can cause hearing loss.
3.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask and thickly
padded gloves.
6
Explanation of general view
9
Clamp nut
10 Loosen
11 Tighten
12 Side handle base
13 Switch lever
14 ON
15 OFF
16 Adjusting dial
17 Power-ON indicator lamp
(green)
18 Service indicator lamp (red)
19 Screwdriver
4.
5.
6.
7.
8.
9.
10. Do not leave the tool running. Operate the tool
11. Do not point the tool at any one in the area when
12. Do not touch the bit or parts close to the bit
SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

ENB009-1
Installing or removing bit
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Clean the bit shank and apply the bit grease provided
to it before installing the bit. (Fig. 1)
Pull the tool holder cover down all the way. (Fig. 2)
Insert the bit into the tool. Turn the bit and push it in
until it engages. (Fig. 3-1)
Release the tool holder cover. It will return automati-
cally to its original position to secure the bit.
(Fig. 3-2)
20 Rear cover
21 Screws
22 Brush holder cap
23 Screws
24 Handle
25 Socket wrench
26 Crank cap
27 Hammer grease
HM1202
Be sure the bit is secured in place before opera-
tion.
Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
Hold the tool firmly with both hands.
Keep hands away from moving parts.
only when hand-held.
operating. The bit could fly out and injure some-
one seriously.
immediately after operation; they may be
extremely hot and could burn your skin.
HM1202C
950 – 1,900
578 mm
9.3 kg

Advertisement

Table of Contents
loading

This manual is also suitable for:

Hm1202c

Table of Contents