Test Mode - Sony hcd-fc7 Service Manual

HCD-FC7
QQ
3 7 63 1515 0
[Version Display Mode]
* The software version is displayed.
Procedure:
Press three buttons of [FUNCTION], x and A (DISC 1)
1.
simultaneously for two seconds.
2. The message "VERSION" is displayed. The version display
mode is activated.
3. Press the NEXT > button. "IF ***" is displayed.
4. Each time the NEXT > button is pressed, the display
changes in the order of DVD, AREA, VERSION and IF.
To exit from this mode, press the ?/1 button.
5.
[Key Test Mode]
* Button check
Procedure:
Press three buttons of [DISPLAY], [FUNCTION] and A (DISC
1.
2) simultaneously.
2. The message "KEY NUM 0" is displayed and "0" blinks.
3. Each time a button is pressed, "KEY NUM 0" value increases.
However, once a button is pressed, it is no longer taken into
account.
4. When all buttons are pressed, "KEY NUM 24" appears and
the number blinking is stopped.
5. To exit from this mode, disconnect the power cord.
[Display Test Mode]
Procedure:
Press three buttons of [BAND], [DISPLAY] and A (DISC 3)
1.
simultaneously.
2. All segments and LEDs are turned on.
TE
L 13942296513
SACD MULTI dts SLEEP TITLE TRK CHAP
D D DIGITAL
DOLBY PLII FMAM
PCMMP3ALL1DISC S
3. When the NEXT > button is pressed, all LEDs are still
turned on and the display will light up as follows.
SACD MULTI dts SLEEP TITLE TRK CHAP
D D DIGITAL
DOLBY PLII FMAM
PCMMP3ALL1DISC S
4. Press the NEXT > button, all LEDs are turned off and
confirm the display.
Press the NEXT > button, all segments are turned off.
5.
6. Every pressing of the NEXT > button turns on each
segments in the same order.
To exit from this mode, press the ?/1 button.
7.
www
.
26
http://www.xiaoyu163.com
SECTION 5

TEST MODE

INDEX H TUNED M MONO S ST NIGHT ALBM
kHz BASS SHUF
MHz PBC PROG
NTSC REP1
INDEX H TUNED M MONO S ST NIGHT ALBM
kHz BASS SHUF
MHz PBC PROG
NTSC REP1
x ao
y
i
http://www.xiaoyu163.com
8
[OSD Test Mode]
Procedure:
Press the ?/1 button on the main unit or the ?/1 button on
1.
the remote commander to turn the set on.
2. Set the FUNCTION to DVD.
3. Press three buttons of A (DISC 1) , . PREV and [VOLUME
+] simultaneously.
4. The message "SERVICE IN" is displayed on the display. The
Test Mode Menu is displayed on the TV screen.
5. To execute each function, select the number on the remote
commander.
6. See the following section for explanation in detail.
7. To exit from this mode, press the ?/1 button.
[Disc Slot Lock]
The disc slot lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure:
1. Turn the set on.
Press two buttons of x and
2.
seconds.
3. The message "LOCKED" is displayed and the slot is locked.
Releasing Procedure:
Press two buttons of x and A simultaneously for five seconds
1.
again.
2. The message "UNLOCKED" is displayed and the slot is
unlocked.
Note : When "LOCKED" is displayed, the slot lock is not released
by turning power on/off with the ?/1 button.
[Repeat Limit Release Mode]
Q Q
3 6 7 1 3
Procedure:
Press three buttons of A (DISC 1) , . PREV and [VOLUME
1.
-] simultaneously.
2. Repeat limit is released.
[CDM Ship Mode]
* This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Turn the set on.
2. Set the function to DVD.
3. Press the x button for five seconds.
4. The message "MECHA LOCK" is displayed.
Press the ?/1 button to turn off. The CDM ship mode is set.
5.
u163
.
2 9 9 4 2 8
A simultaneously for five
1 5 0 5 8 2 9 9 4
m
co
9 9
2 8 9 9