Download  Print this page

Product Dimensions; Cutout Dimensions - KitchenAid KGRS205T Dimension Manual

Architect series ii
Hide thumbs
   

Advertisement

Range

PRODUCT DIMENSIONS

29"
26
/
"
3
4
depth to
backguard
standoffs
Model/serial
number plate (located behind
the storage drawer on the left-hand
side of the oven frame)
*
Range can be raised approximately 1" by adjusting the leveling legs.
For additional information about KitchenAid
or call the Customer Experience Center at 800-422-1230. We'll help you select
the ideal model, answer questions about appliance operation and performance,
06/08
Freestanding Gas
47
/
"*
1
8
35
/
"*
5
8
29
/
"
7
8
Rating number plate (located
behind the storage drawer on the
right-hand side of the oven frame)
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
and give you a point of contact should you ever need service.
®Registered trademark/™Trademark of KitchenAid, U.S.A.
©2008. All rights reserved.
KitchenAid • Benton Harbor, Michigan 49022 U.S.A.

CUTOUT DIMENSIONS

Cabinet opening dimensions shown are for 25" countertop depth,
24" base cabinet depth, and 36" countertop height.
Cabinet opening dimensions shown are for 25" countertop depth,
24" base cabinet depth, and 36" countertop height.
13" max.
upper cabinet depth
30" min.
18"
opening width
upper cabinet
to countertop
18"
upper cabinet
30" min.
to countertop
opening width
Shaded area
6"
3"
recommended
for installation
Shaded area
6"
of rigid gas pipe.
recommended
H
for installation
6"
of rigid gas pipe.
3"
3"
3
/
"
1
4
*
Note: 24" minimum when bottom of wood or metal
cabinet is protected by not less than
millboard covered with not less than No. 28 MSG sheet steel,
*
Note: 24" minimum when bottom of wood or metal
0.015" stainless steel, 0.024" aluminum or 0.020" copper.
cabinet is protected by not less than
/
" flame retardant
1
4
30" minimum clearance between the top of the cooking
millboard covered with not less than No. 28 MSG sheet steel,
platform and the bottom of an unprotected wood or metal cabinet.
0.015" stainless steel, 0.024" aluminum or 0.020" copper.
If installing a hood or microwave hood combination above the
30" minimum clearance between the top of the cooking
range, follow hood or microwave hood combination installation
platform and the bottom of an unprotected wood or metal cabinet.
instructions for dimensional clearances above the cooktop surface.
If installing a hood or microwave hood combination above the
range, follow hood or microwave hood combination installation
instructions for dimensional clearances above the cooktop surface.
Anti-tip bracket:
To install the anti-tip bracket
shipped with the range,
see Installation Instructions.
appliances, visit KitchenAid.com
®
KGRS205T
13" max.
For minimum
clearance to
upper cabinet depth
top of cooktop,
30" min.
For minimum
see Note.*
opening width
clearance to
top of cooktop,
see Note.*
30" min.
opening width
6"
3"
6"
H
Cabinet door or
6"
3
/
"
1
hinge should not
4
extend into the cutout.
3"
3
/
"
1
3"
4
3
/
"
1
4
/
" flame retardant
1
4
(28508RC0608)
Printed in U.S.A.
Cabinet door or
hinge should not
extend into the cutout.

Advertisement

Table of Contents
loading

  Related Manuals for KitchenAid KGRS205T