Download  Print this page

Advertisement

Monitor
Monitor
Two sets of monitor output are provided, MONITOR A and MONITOR B, and you can
independently select the monitor source and adjust the output level for each.
CUE A/B
L R
PRE DELAY
POST DELAY
(CUE)
(CUE)
CUE TRIM
DELAY
STEREO
L
MIX
MONITOR
DIMMER
R
MATRIX
SOURCE
ON CUE
TALKBACK
SELECT
C
INPUT CH
(DIRECT OUT)
OSC
$
PRE DELAY
POST DELAY
2
3
(MONITOR)
4
(MONITOR)
Number of systems
There are two sets of monitor output, MONITOR A and MONITOR B.
1
Headphone output
Two headphone outputs are provided, PHONES A and PHONES B.
2
Input selector
You can provide eight sources to be monitored, and switch between them. The signals of up to
eight channels can be assigned to one monitor source. You can select not only channel or bus
signals, but signals directly from input patches as monitor signals.
3
Monitor circuit structure
This consists of three channels: L-channel, R-channel, and CENTER channel.
INSERT
PLUG-IN
INSERT
5
PRE EQ
POST EQ
)
(CUE)
(CUE)
DIMMER
CUE OUT
ON
LEVEL
CUE PEQ
MODE
TALKBACK
CUE SOLO LOGIC
DIMMER/
MONITOR
MONITOR
DIMMER
LEVEL
OUT
PEQ
ON
MODE
TALKBACK
9
@
6
)
7
CUE
PRE DELAY
POST DELAY
L
MONITOR
L R+C
PHONES
DA
R
PRE DELAY
DOWN-
LEVEL
POST DELAY
MIX
LINK
C
CUE/SOLO
LOGIC
#
!
INSERT
5
4
DELAY
Allows the monitor signal to be delayed. You can specify up to 1000 msec. You can select the
delay time unit from the following: meter, feet, sample, msec, frame, depending on your
application.
5
INSERT
A plug-in, GEQ, or PEQ can be inserted. The insert point is fixed at PRE EQ (immediately
before the EQ). An insert point is also provided for the PHONES OUT.
6
PEQ
The monitor section provides an 8-band parametric EQ specialized for monitoring.
7
MONITOR LEVEL
The MONITOR OUT L-channel, R-channel, and CENTER channel output levels can be
L
adjusted. The monitor level can also be assigned to a fader.
R
8
Output structure
• L-channel, R-channel, and CENTER channel of MONITOR A
L
• L-channel, R-channel, and CENTER channel of MONITOR B
R
C
9
CUE SOLO LOGIC
Causes the CUE signal to interrupt the monitor output when CUE is active. The CENTER
8
channel can be turned on/off independently.
)
DIMMER ON TALKBACK
Attenuates the monitor signal by a fixed amount.
PHONES A-B
Tip
!
PHONES LEVEL LINK
Ring
The level of the signal sent to the PHONES A/PHONES B jacks is linked with the MONITOR A/
Sleeve
MONITOR B LEVEL.
PHONES
LEVEL
@
MONITOR OUT MODE
1
Downmixes the L/R signals to monaural.
This also downmixes the L/R/C signals to L/R.
#
L R+C DOWNMIX
Allows you to downmix the L/R/C signals to L/R.
$
DIMMER ON CUE
When the CUE signal has interrupted the monitor output, this attenuates the signal that is being
input to the monitor.
Monitor assignments and on/off switching can also be assigned to a USER DEFINED key.
28
FAQ
CONTENTS
RIVAGE PM10 Operation Manual

Advertisement

Table of Contents

   Related Manuals for Yamaha rivage pm10

Comments to this Manuals

Symbols: 0
Latest comments: