Maintenance And Service; Maintenance: Frequency And Tasks; Maintenance Tasks - Homeowner - Heat & Glo SL-550TR-E Owner's Manual

Care and operation
Hide thumbs Also See for SL-550TR-E:
Table of Contents

Advertisement

4 4

Maintenance and Service

Any safety screen or guard removed for servicing must be
replaced prior to operating the fi replace.
When properly maintained, your fi replace will give you
many years of trouble-free service. Contact your dealer
to answer questions regarding proper operation, trou-
bleshooting and service for your appliance. Visit www.
heatnglo.com to locate a dealer. We recommend annual
service by a qualifi ed service technician.
A. Maintenance: Frequency and Tasks
Task
Frequency
Glass Cleaning
Seasonally
Surrounds/
Decorative
Annually
Fronts
Remote Control
Seasonally
Venting
Seasonally
Gasket Seal
Annually
and Glass
Inspection
Log Inspection
Annually
Firebox
Annually
Inspection
Control
Annually
Compartment &
Firebox Top
Burner Ignition
Annually
& Operation
B. Maintenance Tasks - Homeowner
Installation and repair should be done by a qualifi ed service
technician only. The appliance should be inspected before
use and at least annually by a professional service person.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service ap-
pointment.
More frequent cleaning may be required due to excessive
lint from carpeting, bedding material, et cetera. It is im-
perative that control compartments, burners and circulat-
ing air passageways of the appliance be kept clean. Any
safety screen, guard, or barrier removed for servicing the
appliance must be replaced prior to operating the appli-
ance.
CAUTION! Risk of Burns! The fi replace shall be turned
off and cooled before servicing.
Heat & Glo • SL-550/750TR-E, SL-550/750/950TR-IPI-E Owner's Manual • 2118-911 Rev. B • 2/16
To be completed by
Homeowner
Qualifi ed Service
Technician
Glass Cleaning
Frequency: Seasonally
By: Homeowner
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
CAUTION! Handle fi xed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
• Prepare a work area large enough to accommodate fi xed
glass assembly and door frame by placing a drop cloth
on a fl at, stable surface.
Note: Fixed glass assembly and gasketing may have res-
idue that can stain carpeting or fl oor surfaces.
• Remove door or decorative front from fi replace and set
aside on work surface.
WARNING! Risk of Asphyxiation! Handle fi xed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fi replace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
Removing Fixed Glass Assembly
• Pull the four glass assembly latches out of the groove on
the glass frame. Remove glass door from the appliance
See Figure 4.1.
Replacing Fixed Glass Assembly
• Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove on
the glass frame.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
• Carefully set fi xed glass assembly in place on fi replace.
Hold glass in place with one hand and secure glass
latches with the other hand.
• Reinstall door or decorative front.
13

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents