Setting The Marker Indications - Sony F23 Operation Manual
Digital cinematography camera
Hide thumbs
Also See for F23:
- Operation manual (102 pages) ,
- Specifications (21 pages) ,
- Brochure & specs (20 pages)
Table of Contents
Advertisement
CAM: Optical reception level on the camera side
VTR: Optical reception level on the SRW-1 side
The status of the level is indicated with eight segments.
If 6 to 8 segments are lit: Normal
If 3 to 5 segments are lit: Cautioning level
If only 1 or 2 segments are lit: Warning level
If no segment is lit: No signal or unusable level
For details, refer to the Operation Manual of the CA-F101.
3-6-4 Setting the Marker Indications
The various markers, such as the center marker and safety
zone marker, can be displayed on the viewfinder and
monitor screens.
Example: Center marker (entire cross)
Example: Safety zone marker (90%)
The <CHAR/MARK MIX> page and <MARKER
SETTING> page of the USER (OPERATION) menu allow
you to switch the display of the markers on or off and to set
the display conditions of the markers.
Activating/deactivating all the marker
indications for each output
The <CHAR/MARK MIX> page permits you to activate
and deactivate the marker indications for each output.
<CHAR/MARK MIX> page
< C H A R / M A R K M I X >
U 0 9
V F 1 V F 2 M O N I V B S
C H A R
:
O N
O N
O N
O N
M A R K E R :
O N
O N
O N
O N
B
C U R S O R : O F F O F F O F F
Z E B R A : O F F O F F O F F
O F F
C H A R / M A R K L E V E L : 5 0
V F G A T E M A R K E R : O F F
The MARKER indications are activated for all the outputs
at the factory.
Item
Setting
VF1
Turn all the markers on or off on the
viewfinder connected to the VF1 connector.
VF2
Turn all the markers on or off on the
viewfinder connected to the VF2 connector.
MONI
Turn all the markers on or off on the monitors
connected via the MONITOR OUT
connectors.
VBS
Turn all the markers on or off on the monitors
connected via the TEST OUT and REMOTE
connectors.
The CHAR/MARK LEVEL line permits you to adjust the
brightness (0 to 50) of the character and marker
indications.
Specifying the markers to be displayed
For the outputs for the total marker indication is activated
on the <CHAR/MARK MIX> page, select and adjust the
marker(s) to be displayed on the next <MARKER
SETTING> page.
<MARKER SETTING> page
< M A R K E R S E T T I N G > U 0 3
C E N T E R
:
O F F
1
B
S A F E T Y
: O F F
9 0 . 0 %
E F F E C T I V E : O F F
A S P E C T
: O F F
4 : 3
V A R I A B L E : - -
S A F E T Y
: O F F
9 0 . 0 %
M A S K
: O F F
1 2
C U R S O R
: B O X
P O S I H / V :
0
0
S I Z E W / H :
9 6 0
5 4 0
All the markers have been set to OFF at the factory.
Item
Setting
CENTER
Set to ON to display the center marker and
select the type of the center marker.
1: Entire cross
2: Entire cross with a hole
3: Center
4: Center with a hole
SAFETY
Set to ON to display the safety zone marker
and specify the range (80%, 90%, 92.5%, or
95%).
EFFECTIVE
Set to ON to display the effective pixel area.
ASPECT
Set to ON to display the aspect marker and
specify the aspect:
2.40:1, 2.35:1, 1.85:1, 1.66:1, 16:9, 15:9,
14:9, 13:9, 4:3, VAR H, VAR V
VARIABLE
If you select VAR H or VAR V for ASPECT,
set the H or V value.
VAR H: 12 to 1920
VAR V: 12 to 1080
Page 48
Advertisement
Table of Contents
