Page 1 © 1997 Compaq Computer Corporation. All rights reserved. Printed in the U.S.A. Compaq and LTE are registered in the U. S. Patent and Trademark Office. Armada is a trademark of Compaq Computer Corporation. Microsoft, MS-DOS, and Windows are registered trademarks of Microsoft Corporation.
Page 2: Table Of Contents
Preface Symbols......................ix Technician Notes ....................ix Serial Number ..................... x Locating Additional Information................ x Chapter 1 Product Description 1.1 ArmadaStation Features................1-1 1.2 ArmadaStation Components..............1-4 Activity Lights.....................1-8 MultiBay......................1-8 Half-Height Bay ..................1-8 Security Lock....................1-9 PC Card Slots ....................1-9 Regional Modem and Ethernet Differences..........1-10 PCI and ISA Expansion Boards ..............1-10...
Page 4 6.5 Enclosure Cover..................6-6 6.6 Module Assembly ..................6-7 6.7 Power Supply..................6-11 6.9 MultiBay/PC Card Assembly ..............6-12 Chapter 7 Specifications 7.1 ArmadaStation Physical and Environmental Specifications....7-1 7.2 Armada MiniStation Physical and Environmental Specifications ...7-2 Appendix A Connector Pin Assignments ................A-1 Appendix B Power Cord Set Requirements 3-Conductor Power Cord Set................
Page 5: Preface
ArmadaStation and Armada MiniStation E and EX without notice. Additional information is available on the Compaq ArmadaStation and Armada MiniStation E and EX Illustrated Parts Map. Information for the Compaq Armada 7700 Family of Personal Computers is available in the Compaq Armada 7700 Family of Personal Computers Maintenance and Service Guide and Illustrated Parts Map.
Page 6: Serial Number
Serial Number When requesting information or ordering spare parts, provide the ArmadaStation or Armada MiniStation serial number. The ArmadaStation serial number is located on the right side below the PCI/ISA expansion slots; the Armada MiniStation serial number is located on the left side above the power button.
Page 7: Product Description
Chapter 1 Product Description 1.1 ArmadaStation Features The Compaq ArmadaStation provides fully integrated desktop capabilities for the Compaq Armada 7000 Family of Personal Computers. The ArmadaStation eliminates the need to disconnect external devices when you remove the computer. Figure 1-1. Compaq ArmadaStation...
Page 8 Up to three CD-ROM drives installed as follows: – Three CD-ROM drives: The two drives in the ArmadaStation must be used for data; the CD-ROM drive in the computer can then be used for audio or data.
Page 10: Armadastation Components
........1.2 ArmadaStation Components The external components on the top, front, and right side of the ArmadaStation are shown in Figure 1-2 and described in Table 1-1.
Page 11 ........Additional components on the front and right sides of the ArmadaStation are shown in Figure 1-3 and described in Table 1-2.
Page 12 ........The components on the rear panel and left side of the ArmadaStation are shown in Figure 1-4 and described in Table 1-3.
Page 13 ........The external connectors on the right side and rear panel of the ArmadaStation are shown in Figure 1-5 and described in Table 1-4.
Page 14: Activity Lights
Compaq LTE Elite and LTE 5000 hard drives that are configured for use as secondary drives can be used in the ArmadaStation MultiBay. A hard drive must be inserted in an Armada 7000 Hard Drive MultiBay Adapter before it can be inserted in a MultiBay.
Page 15: Security Lock
NOTE: The PC Card security post must first be put in place before the security lock will prevent PC Cards from being removed from the ArmadaStation. PC Card Slots The ArmadaStation has two PC Card slots. The slots support one of the following PC Card combinations: Two Type I or Type II PC Cards One Type III PC Card in the top slot and a Type I or Type II in the bottom slot.
Page 16: Regional Modem And Ethernet Differences
........Regional Modem and Ethernet Differences The modem and Ethernet connectors found on the ArmadaStation vary by region. Refer to the following table for modem and Ethernet differences:...
Page 17: Armada Ministation Features
........1.3 Armada MiniStation Features The Compaq Armada MiniStation provides fully integrated desktop capabilities for the Compaq Armada 7000 Family of Personal Computers. The Armada MiniStation eliminates the need to disconnect external devices when you undock the computer from the Armada MiniStation.
Page 19: Armada Ministation Components
........1.4 Armada MiniStation Components The external components on the top and right side of the Armada MiniStation are shown in Figure 1-7 and described in Table 1-7.
Page 20 ........The components on the left side of the Armada MiniStation are shown in Figure 1-8 and described in Table 1-8.
Page 21 ........The external components and connectors on the rear panel of the Armada MiniStation are shown in Figure 1-9 and described in Table 1-9.
Page 22: Activity Lights
Second battery pack Diskette drive Compaq LTE Elite and LTE 5000 hard drives that are configured for use as secondary drives can be used in the Armada MiniStation EX MultiBay. A hard drive must be inserted in an Armada 7000 Hard Drive MultiBay Adapter before it can be inserted in a MultiBay.
Page 23: Pc Card Slots
........PC Card Slots The ArmadaStation MiniStation EX has two PC Card slots. The slots support one of the following PC Card combinations: Two Type I or Type II PC Cards One Type III PC Card in the top slot and a Type I or Type II in the bottom slot.
Page 24: Troubleshooting
When the problem is resolved, stop performing the troubleshooting steps and do not complete the remaining recommended actions. Refer to Chapters 5 and 6 for any recommended removal and replacement procedures. If the problem is intermittent, check the ArmadaStation or Armada MiniStation several times to verify that the problem is solved. Before Replacing Parts...
Page 25: Solving Docking And Undocking Problems
The computer is not properly Undock the computer and redock it. docked or will not dock. seated in the docking system. No AC power. Release the computer from the docking mechanism by sliding the ArmadaStation manual release lever to the right. Troubleshooting...
Page 26: Solving Expansion Board Problems
The following are some common problems to check first. Refer to the table below for additional problems and solutions. Ensure that the cabling is securely attached to the ArmadaStation or Armada MiniStation. A loose cable is the most common cause of network problems. If the cable is loose, secure it and determine if the computer can communicate with the network.
Page 27 ........Table 2-3 Solving Ethernet Network Problems Problem Probable Cause Recommended Action(s)
Page 28 The files for the network Reinstall the network drivers. drivers have been corrupted. IMPORTANT: If the 100BaseT Ethernet upgrade module has been installed, remove it before returning the Ethernet module, ArmadaStation, or Armada MiniStation for replacement. Troubleshooting...
Page 30: Illustrated Parts Catalog
........Chapter 3 Illustrated Parts Catalog This chapter provides an illustrated parts breakdown and a reference for spare part numbers for the Compaq ArmadaStation and Armada MiniStation. Illustrated Parts Catalog...
Page 31: Armadastation Components
........3.1 ArmadaStation Components Figure 3-1. ArmadaStation Components Illustrated Parts Catalog...
Page 33: Miscellaneous Base Plastics Kit Components
........3.2 Miscellaneous Base Plastics Kit Components Figure 3-2.
Page 34: Miscellaneous Base Hardware Kit Components
........3.3 Miscellaneous Base Hardware Kit Components Figure 3-3.
Page 35: Miscellaneous Cable Kits
........3.4 Miscellaneous Cable Kits Figure 3-4.
Page 36 Drive power cable Hard drive cable (7”) Diskette drive cable Table 3-5 Control Panel Cable Kit Spare Part Number 272123-001 Item Description Control panel cable Table 3-6 ArmadaStation MultiBay Cable Kit Spare Part Number 298061-001 Item Description MultiBay cable Illustrated Parts Catalog...
Page 37: Miscellaneous Cable Kit Components
........3.5 Miscellaneous Cable Kit Components Figure 3-5.
Page 38: Miscellaneous
3.7 Documentation Table 3-9 Spare Parts: Documentation Description Spare Part Number Compaq ArmadaStation and Armada MiniStation Maintenance & Service Guide 296390-001 Compaq ArmadaStation and Armada MiniStation Illustrated Parts Map 296391-001 Compaq ArmadaStation and Armada MiniStation Installation and Operations Guide (both guides included in spare kit)
Page 39: Armada Ministation Components
........3.8 Armada MiniStation Components Figure 3-6.
Page 41: Miscellaneous Enclosures Kit Components
........3.9 Miscellaneous Enclosures Kit Components Figure 3-7.
Page 42: Miscellaneous Plastics Kit Components
........3.10 Miscellaneous Plastics Kit Components Figure 3-8.
Page 43: Multibay/Pc Card Assembly
........3.11 MultiBay/PC Card Assembly Figure 3-9.
Page 45: Armadastation And Armada Ministation Options
........3.12 ArmadaStation and Armada MiniStation Options Figure 3-10. ArmadaStation and Armada MiniStation Options 3-16...
Page 47: Miscellaneous
3.14 Documentation Table 3-16 Spare Parts: Documentation Description Spare Part Number Compaq ArmadaStation and Armada MiniStation Maintenance & Service Guide 296390-001 Compaq ArmadaStation and Armada MiniStation Illustrated Parts Map 296391-001 Compaq ArmadaStation and Armada MiniStation Installation and Operations Guide (both guides included in spare kit)
Page 48: Removal And Replacement Preliminaries
........Chapter 4 Removal and Replacement Preliminaries This chapter provides general service information for the Compaq ArmadaStation and Armada MiniStation. Adherence to the procedures and precautions described in this chapter is essential for proper service.
Page 49: Preventing Electrostatic Damage To Equipment
........Preventing Electrostatic Damage to Equipment Many electronic components are sensitive to ESD.
Page 50: Grounding Methods
........Grounding Methods The method for grounding must include either a wrist strap or a foot strap at a grounded workstation.
Page 51: Grounding Equipment
........Grounding Equipment Use the following equipment to prevent static electricity damage to equipment: Wrist Straps are flexible straps with a minimum of one megohm +/- 10% resistance in the ground cords.
Page 52: Service Considerations
Diagnostics software Screws The screws used in the ArmadaStation or Armada MiniStation are not interchangeable. If an incorrect screw is used during the reassembly process, it can damage the unit. Compaq strongly recommends that all screws removed during disassembly be kept with the part that was removed, then returned to their proper locations.
Page 53: Cables And Connectors
Handle flex cables with extreme care; they can tear easily. CAUTION: When servicing the ArmadaStation or Armada MiniStation, ensure that cables are placed in their proper location during the reassembly process. Improper cable placement can damage the ArmadaStation or Armada MiniStation.
Page 54: Armadastation Removal And Replacement Procedures
Chapter 5 ArmadaStation Removal and Replacement Procedures This chapter presents the removal and replacement procedures for the ArmadaStation. 5.1 Serial Number The ArmadaStation serial number should be reported to Compaq when requesting information or ordering spare parts. The serial number is displayed on the right side of the ArmadaStation, below the expansion slot connectors (Figure 5-1).
Page 55: Disassembly Sequence Chart
........5.2 Disassembly Sequence Chart Use the chart below to determine the section number and disassembly sequence for removing components from the ArmadaStation. 5.3 Preparing the ArmadaStation for Disassembly 5.4 External Components...
Page 56: Preparing The Armadastation For Disassembly
5. Disconnect the power cord from the ArmadaStation Figure 5-3. Disconnecting the ArmadaStation 6. Disconnect any external devices. 7. If installed, remove any MultiBay devices from the ArmadaStation MultiBays. 8. If installed, remove any PC Cards from the ArmadaStation PC Card slots. ArmadaStation Removal and Replacement Procedures...
Page 57: External Components
Alignment tray assembly Compaq Logo You need to install a Compaq logo on the ArmadaStation or monitor support cover only if the old logo is damaged or removed. The logo is an adhesive-backed label. Remove the protective covering from the adhesive back, and install the logo in its location on the ArmadaStation (Figure 5-4) The logo reads from left to right when viewed from the front of the unit.
Page 58: Armadastation Feet
........ArmadaStation Feet The feet for the ArmadaStation are rectangular, adhesive-backed rubber pads. Install the feet by removing the protective covering from the adhesive back and placing the feet in their positions on the bottom of the ArmadaStation (Figure 5-5).
Page 59: Alignment Tray Assembly
........Alignment Tray Assembly The alignment tray assembly is used to align the computer on the ArmadaStation. The left side of the computer should be aligned with the left side of the alignment tray assembly when docking the computer.
Page 60 2. Align the tabs in the back of the alignment tray assembly with the slots in the upper case assembly (Figure 5-7). 3. Push the alignment tray assembly into place on the upper case assembly. Figure 5-7. Installing the Alignment Tray Assembly ArmadaStation Removal and Replacement Procedures...
Page 61: Rear Panel Assembly
To remove the rear panel assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Position the ArmadaStation so the rear panel is facing forward. 3. Slide the rear panel release latch to the left (Figure 5-8).
Page 62 NOTE: Once the rear panel assembly has been removed, the manual release lever is accessible (Figure 5-9). When this lever is moved to the right, the mechanism assembly, which secures the computer when it is docked in the ArmadaStation, releases and allows the computer to be manually undocked.
Page 63 3. Swing down the bottom edge of the rear panel assembly until it latches onto the base assembly. NOTE: When installing the rear panel assembly, make sure the BNC Ethernet connector (if present) does not interfere with the assembly. 4. Slide the rear panel release latch to the right. 5-10 ArmadaStation Removal and Replacement Procedures...
Page 64: Upper Case Assembly
To remove the upper case assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Position the ArmadaStation so the front is facing forward. 3. Remove the alignment tray assembly (Section 5.4). 4. Remove the rear panel assembly (Section 5.5).
Page 65 6. Grasp the back of the upper case assembly, lift up on the back of the assembly, and swing it forward (Figure 5-12). Figure 5-12. Removing the Upper Case Assembly 7. Set aside the upper case assembly. 5-12 ArmadaStation Removal and Replacement Procedures...
Page 66 3. Replace the three upper case screws. NOTE: When installing the upper case assembly, make sure the ribs on the center of the base assembly are engaged in the slot in the front of the upper case assembly. ArmadaStation Removal and Replacement Procedures 5-13...
Page 67: Drive Cage Shield
The drive cage shield is located in the base assembly and covers the half-height bay assemblies. To remove the drive cage shield, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4).
Page 68 NOTE: Make sure the screw installed on the right side of the drive cage shield secures the control panel assembly ground strap to the drive cage shield. Figure 5-15. Installing the Drive Cage Shield ArmadaStation Removal and Replacement Procedures 5-15...
Page 69: Half-Height Bays
3. Lift the half-height drive out of the base assembly. Reverse the removal procedure described above to reinstall a half-height drive. If a half-height drive is being installed in the ArmadaStation left half-height bay for the first time, complete these steps: 1.
Page 71 NOTE: The half-height drive should have two screws installed in each side. If these screws are missing, appropriate-sized screws must be obtained to secure the half-height drive to the drive cage shield. Figure 5-17. Removing the Half-Height Drive Screws 5-18 ArmadaStation Removal and Replacement Procedures...
Page 72 (Figure 5-18). NOTE: The drive cage should be aligned so the “L” and “LEFT” indicators can be read when the half-height drive is installed in the ArmadaStation left half-height bay. Figure 5-18. Aligning the Half-Height Drive with the Drive Cage...
Page 74 Figure 5-20. Installing a Half-Height Drive 8. Attach the appropriate cable to the connectors on the half-height drive and the ArmadaStation. Refer to the documentation that came with the half-height drive for information about which ArmadaStation connectors to use. Reverse the installation procedure described above to remove a half-height drive.
Page 75: Half-Height Multibay Adapters
Reverse the removal procedure described above to reinstall a half-height MultiBay adapter. Installing a Half-Height MultiBay Adapter If a half-height MultiBay adapter is being installed in the ArmadaStation left half-height bay for the first time, complete these steps: 1. Remove the drive cage shield (Section 5.7).
Page 76 3. Remove the half-height bay blank bezel cover from the drive cage. 4. Remove the screws from the sides of the half-height MultiBay adapter (Figure 5-22). Figure 5-22. Removing the Half-Height MultiBay Adapter Screws ArmadaStation Removal and Replacement Procedures 5-23...
Page 77 5. Place the drive cage over the half-height MultiBay adapter. Align the front of the adapter with the tab on the front of the drive cage (Figure 5-23). Figure 5-23. Aligning the Half-Height MultiBay Adapter with the Drive Cage 5-24 ArmadaStation Removal and Replacement Procedures...
Page 79 Figure 5-25. Alignment of the Security Extension Bar NOTE: Step 7 is not necessary when installing a Compaq LTE 5000 Half-Height MultiBay Adapter. 8. Turn the drive cage/half-height MultiBay adapter assembly right side up.
Page 80 MultiBay installed in the right half-half bay. Align the holes on the drive cage with the alignment pins in the base assembly (Figure 5-26). Figure 5-26. Installing the Half-Height MultiBay Adapter Assembly ArmadaStation Removal and Replacement Procedures 5-27...
Page 82 11. Connect the hard drive cable to its respective connectors on the half-height MultiBay adapter and backplane assembly (Figure 5-28). Figure 5-28. Connecting the Hard Drive Cable to the Armada 7000 Half-Height MultiBay Adapter and Backplane Assembly ArmadaStation Removal and Replacement Procedures 5-29...
Page 83 MultiBay cable fits flush in the plastic connector housing on the half-height MultiBay adapter. Figure 5-29. Connecting the MultiBay Cable to the Armada 7000 Half-Height MultiBay Adapter Reverse the installation procedure described above to remove a half-height MultiBay adapter. 5-30 ArmadaStation Removal and Replacement Procedures...
Page 84: I/O Assembly
WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching the I/O board. To remove the I/O assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the rear panel assembly (Section 5.5). ArmadaStation Removal and Replacement Procedures...
Page 85 CAUTION: Be careful when removing the I/O assembly. The assembly includes a multiple-pin connector that is firmly connected to the backplane assembly. Pull firmly to disconnect the I/O assembly from the backplane assembly. Figure 5-31. Removing the I/O Assembly 5-32 ArmadaStation Removal and Replacement Procedures...
Page 86 ........To install the 100BaseTX Ethernet module, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the rear panel assembly (Section 5.5).
Page 87 To install the I/O assembly, follow these steps: 1. Align the right side of the I/O bracket with the groove in the expansion card cage (Figure 5-33). 2. Slide the I/O assembly into the ArmadaStation until the assembly connector seats itself on the backplane assembly.
Page 88: Top Brace
To remove the top brace, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3. Remove the rear panel assembly (Section 5.5).
Page 90 2. Swing down the back edge of the top brace until the brace is resting on the base assembly and power supply Figure 5-36. Installing the Top Brace 3. Install the two screws securing the top brace to the base assembly and power supply. ArmadaStation Removal and Replacement Procedures 5-37...
Page 91: Left Speaker Assembly
The left speaker assembly consists of the left speaker, its cover, and its insulator. To remove the left speaker assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3. Remove the rear panel assembly (Section 5.5).
Page 92: Control Panel Cable
The control panel cable connects the control panel to the backplane connector and is spared as a unit. To remove the control panel cable, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3. Remove the rear panel assembly (Section 5.5).
Page 93: Control Panel Assembly
Suspend lightpipe C/U actuator To remove the control panel assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3. Remove the rear panel assembly (Section 5.5). 4. Remove the upper case assembly (Section 5.6).
Page 94 7. Remove the three screws securing the control panel assembly to the base assembly (Figure 5-39). 8. Lift the control panel assembly and control panel cable from the base assembly. Figure 5-39. Removing the Control Panel Assembly ArmadaStation Removal and Replacement Procedures 5-41...
Page 96 NOTE: Make sure the control panel spacer fits flush against the top and right edges of the sheetmetal on the lower case. Figure 5-41. Replacing the Control Panel Spacer ArmadaStation Removal and Replacement Procedures 5-43...
Page 97 The connectors are properly seated and connected when the plastic connector housing on the control panel cable fits flush in the plastic connector housing on the control panel assembly. 5-44 ArmadaStation Removal and Replacement Procedures...
Page 98 Figure 5-43. Installing the Control Panel Assembly NOTE: Make sure the control panel cable does not get pinned underneath the control panel assembly. The cable should rest in the right half-height bay when the control panel assembly is installed. ArmadaStation Removal and Replacement Procedures 5-45...
Page 99 C/U actuator into the proper position by pushing down on the actuator tab (Figure 5-44). Figure 5-44. Tripping the C/U Actuator 6. Install the screws securing the control panel assembly to the base assembly. 5-46 ArmadaStation Removal and Replacement Procedures...
Page 100 The connectors are properly seated and connected when the plastic connector housing on the control panel cable fits flush in the plastic connector housing on the backplane assembly. ArmadaStation Removal and Replacement Procedures 5-47...
Page 101 Figure 5-46. 3. Remove the backing from the backplane-brace spacer and insert it between the backplane assembly and the subpan side shield. Figure 5-46. Replacing the Subpan Side Shield and Backplane-Brace Spacer 5-48 ArmadaStation Removal and Replacement Procedures...
Page 102 However, if it should be removed, refer to Figure 5-47 for the proper position of the security actuator , torsion spring , and MultiBay security arm Figure 5-47. Proper Position of the C/U Actuator Assembly ArmadaStation Removal and Replacement Procedures 5-49...
Page 103: Expansion Boards
........5.14 Expansion Boards The ArmadaStation provides two slots for 32- or 64-bit PCI expansion boards and two slots for 16-bit, full-length ISA expansion boards. Any combination of two of these boards can be installed in the ArmadaStation.
Page 104 Reverse the installation procedure described above to remove an expansion board. Once an expansion board has been installed, its internal connector can be accessed on the lower right side of the ArmadaStation. If the expansion board has a cable, refer to the documentation included with the board for connection information.
Page 105: Mechanism Assembly
The assembly is spared as a unit and should not be disassembled. To remove the mechanism assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3. Remove the rear panel assembly (Section 5.5).
Page 107 9. Remove the mechanism assembly by pressing down on the two square tabs on the mechanism assembly cover and pulling the assembly out of the backplane assembly (Figure 5-52). Figure 5-52. Removing the Mechanism Assembly Reverse the removal procedure described above to install the mechanism assembly. 5-54 ArmadaStation Removal and Replacement Procedures...
Page 108: Power Supply
........5.16 Power Supply The power supply is located in the left rear corner of the ArmadaStation. It is replaced as an assembly with its fan. To remove the power supply, follow these steps: CAUTION: Do not handle or carry the power supply by the wiring harness.
Page 109 9. Remove the power supply from the base assembly Figure 5-53. Removing the Power Supply Reverse the removal procedure described above to install the power supply assembly. 5-56 ArmadaStation Removal and Replacement Procedures...
Page 110: Backplane Assembly
11. Remove any installed PCI or ISA expansion boards from the backplane assembly (Section 5.14). 12. Remove the mechanism assembly (Section 5.15). 13. Remove the power supply (Section 5.16). 14. Position the ArmadaStation so the front is facing forward. ArmadaStation Removal and Replacement Procedures 5-57...
Page 111 NOTE: When removing the backplane assembly, do not use the heatsink to lift the assembly. Figure 5-54. Removing the Backplane Assembly Reverse the removal procedure described above to install the backplane assembly. 5-58 ArmadaStation Removal and Replacement Procedures...
Page 112: Expansion Card Cage
7. Disconnect and untuck the control panel cable from the backplane assembly (Section 5.13). 8. Remove the mechanism assembly (Section 5.15). 9. Remove the power supply (Section 5.16). 10. Remove the backplane assembly (Section 5.17). 11. Position the ArmadaStation so the left side is facing forward. ArmadaStation Removal and Replacement Procedures 5-59...
Page 113 12. Flex the right bottom side of the expansion card cage away from the retainer on the base assembly and swing the cage up and away (Figure 5-55). Figure 5-55. Releasing the Expansion Card Cage 5-60 ArmadaStation Removal and Replacement Procedures...
Page 114 13. Swing the expansion card cage to the right until the tabs on the right side of the cage clear the slots in the base assembly (Figure 5-56). Figure 5-56. Removing the Expansion Card Cage Reverse the removal procedure described above to install the backplane assembly. ArmadaStation Removal and Replacement Procedures 5-61...
Page 115: Armada Ministation Removal And Replacement Procedures
Otherwise, “E” or “EX” is used to indicate the specific model base. 6.1 Serial Number The Armada MiniStation serial number should be reported to Compaq when requesting information or ordering spare parts. The serial number is displayed on the left side of the Armada MiniStation (Figure 6-1).
Page 116: Disassembly Sequence Chart
Use the chart below to determine the section number and disassembly sequence for removing components from the Armada MiniStation. 6.3 Preparing the Armada MiniStation for Disassembly 6.4 External Components Compaq Logo Armada MiniStation Feet 6.5 Enclosure Cover 6.6 Module Assembly 6.7 Power Supply 6.8 MultiBay/PC Card Assembly...
Page 117: Preparing The Armada Ministation For Disassembly
........6.3 Preparing the Armada MiniStation for Disassembly Before beginning removal and replacement procedures, follow these steps: 1.
Page 118: External Components
Feet Compaq Logo A Compaq logo should be installed on the Armada MiniStation or monitor support cover only if the old logo is damaged or removed. The logo is an adhesive-backed label. Remove the protective covering from the adhesive back, and install the logo in its location on the Armada MiniStation (Figure 6-4).
Page 119: Armada Ministation Feet
........Armada MiniStation Feet The feet for the Armada MiniStation are round, adhesive-backed rubber pads.
Page 120: Enclosure Cover
........6.5 Enclosure Cover The enclosure cover is spared as a unit.
Page 121: Module Assembly
........6.6 Module Assembly The module assembly is located underneath the enclosure cover.
Page 122 ........5. Position the Armada MiniStation so the left side is facing forward. 6.
Page 123 ........8. Lift the module assembly away from the base assembly (Figure 6-9). NOTE: The Armada MiniStation EX module assembly includes a multiple-pin connector that is firmly connected to the MultiBay/PC Card assembly.
Page 124 ........To install the module assembly, follow these steps: 1.
Page 125: Power Supply
........6.7 Power Supply The screws securing the module assembly to the base assembly also secure the power supply.
Page 126: Multibay/Pc Card Assembly
The MultiBay/PC Card Assembly provides the Armada MiniStation EX with a MultiBay, a battery charging bay, and two PC Card slots. MultiBay devices supported by the computer and ArmadaStation can be used in the Armada MiniStation EX. CAUTION: Be careful when removing and installing the MultiBay/PC Card assembly. The assembly includes a multiple-pin connector that must be connected to the module assembly.
Page 127 ........3. Remove the five screws securing the MultiBay/PC Card assembly to the base assembly (Figure 6-12).
Page 128: Specifications
........Chapter 7 Specifications This chapter provides physical and performance specifications for the ArmadaStation and Armada MiniStation. 7.1 ArmadaStation Physical and...
Page 129: Armada Ministation Physical And Environmental Specifications
0.75 G, 10 to 500 Hz sine 0.5 octave/min sweep Heat Dissipation Btu/hr kg-cal/min Monitor support cover(maximum) 55 lb 25 kg The ArmadaStation and Armada MiniStation are designed in accordance with ANSI specifications (no. X3.131-1993, Rev 10h) and IEEE 802.3 specifications. Specifications...
Page 130: Connector Pin Assignments
........Appendix A Connector Pin Assignments This appendix contains the pin assignments for all external connectors. Table A-1 Headphone Jack (ArmadaStation only) Connector Signal Audio out Ground Table A-2...
Page 132 Stereo Line-out Jack Connector Signal Audio out Ground Table A-8 Stereo Line-in Jack Connector Signal Audio in Ground Table A-9 MIDI/JoystickConnector (ArmadaStation only) Signal Signal Ground Ground Joystick Button Joystick Button Joystick Direction Joystick Direction Ground MIDI Out Ground Joystick Direction...
Page 137 Connector Pin Assignments...
Page 138: Power Cord Set Requirements
100 to 120 or 220 to 240 volts AC. The power cord sets received with the ArmadaStation and Armada MiniStation meet the requirements for use in the country where the equipment is purchased.
Page 139: Country-Specific Requirements
........Country-Specific Requirements 3-Conductor Power Cord Set Requirements—By Country Country Accredited Agency Applicable Note Numbers...
Page 140 1-4 requirements, B-1 3-16 depth, 7-1 activity lights Installation and Operations disassembly sequence chart, Armada MiniStation, 1-16 Guide ArmadaStation, 1-8 spare part number, 3-7, documentation, 3-7, 3-16 additional information, x 3-16 external components, 5-4 alignment Maintenance and Service external connectors...
Page 141 1-15 5-39 documentation ArmadaStation Armada MiniStation, 3-7, illustrated, 1-7 illustrated, 3-6 3-16 regional availability, 1-10 spare part number, 3-7 ArmadaStation, 3-7, 3-16 pinout, A-4 removing from drive cage ArmadaStation, 5-39 ArmadaStation routing in ArmadaStation, illustrated, 3-2, 3-5 5-47 shield...
Page 142 Armada ArmadaStation, 7-1 ArmadaStation, 1-10 MiniStation, 6-5 humidity troubleshooting, 2-3 installing on Armada MiniStation, 7-2 expansion board ArmadaStation, 5-5 installing in ArmadaStation, 5-50 troubleshooting:, 2-3 I/O assembly half-height expansion card cage ArmadaStation bays, 5-16 ArmadaStation illustrated, 3-2 ArmadaStation, 1-8...
Page 143 3-9 spare part number, 3-7 Installation and Operations LTE 5000 Half-Height Guide miscellaneous plastics kit MultiBay Adapter ArmadaStation and Armada Armada MiniStation, 3-11 illustrated, 3-14 MiniStation spare part number, 3-1 option part number, 3-15 spare part number, 3-7,...
Page 144 ArmadaStation PCI expansion board monitor support cover slots illustrated, 1-5 ArmadaStation, 1-10 ArmadaStation installation, 5-50 illustrated, 1-4 location, 5-51 mouse connector installing in ArmadaStation, network pinout, A-2 5-50 troubleshooting, 2-3 MultiBay PCI/ISA expansion slots activity light ArmadaStation Armada MiniStation EX...
Page 146 1-6 technician notes, ix illustrated, 1-7 volume control temperature regional availability, 1-10 ArmadaStation Armada MiniStation, 7-2 illustrated, 1-5 ArmadaStation, 7-1 volume/mute button top brace component of control panel ArmadaStation undocking assembly, 5-40 illustrated, 3-2, 3-5 troubleshooting, 2-2 installing on...
Page 147: Index
........I-8 Index...

This manual is also suitable for:

Armada ministation e Armada ministation ex

Compaq ArmadaStation Maintenance And Service Manual

Chapter 1 Product Description

Chapter 2 Troubleshooting

Chapter 3 Illustrated Parts Catalog

Chapter 4 Removal and Replacement Preliminaries

Chapter 5 Armadastation Removal and Replacement Procedures

Chapter 6 Armada Ministation Removal and Replacement Procedures

Chapter 7 Specifications

Appendix A

Connector Pin Assignments

Appendix B Power Cord Set Requirements

Index

Quick Links

Related Manuals for Compaq ArmadaStation

Summary of Contents for Compaq ArmadaStation

This manual is also suitable for:

Table of Contents