LAN Control Utility User Manual (for FL7000U) Preparation/SetUp ...2 Preparation before using the network function ...2 Connection ...3 Installation ...3 Setting the IP address of the projector ...5 When using a DHCP server ...6 When not using a DHCP server ...7 Telnet setting ...8...
Preparation/SetUp Preparation before using the network function This projector is equipped with the network function to control and monitor the projector’s operations using a Web browser and to send e-mail notifi cation. Before using the network function, perform the following three preparation steps.
Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged • from your body, causing damage to the projector. Installation Before starting installation, be sure to read “ReadMe.txt” contained in the CD-ROM.
Page 4
When the installation process is completed, click Close. How to remove Projector-Control Device Installer Select [Start] - [Control Panel] - [Add or Remove Programs] - [Projector-Control Device Installer] and click [Remove] ® (in the case of Windows XP).
Preparation/SetUp (continued) Setting the IP address of the projector Before setting the IP address, check that the projector has been LAN-networked and turn on the main power of the projector. Start the Projector-Control Device Installer. • Select [Start] - [All Programs] - [Projector] -...
Preparation/SetUp (continued) When using a DHCP server Select [Obtain an IP address automatically] and click Next. Click Next. • Check that the options are marked with check- marks as shown on the right. Keep them un- changed for normal use. Click Assign.
Preparation/SetUp (continued) When not using a DHCP server Select [Assign a specifi c IP address] and click Next. Enter a fi xed IP address (for example, 192.168.0.1) and click Next. (Note) Do not use 0 or 255 for the last digit of the IP address.
This section describes how to set the password, display language on the ProjectorView screen, LAN control, and PJLink™ certifi cation that are necessary for the operation state control tool (commercially available) that uses the projector operation control/monitor tool ProjectorView and the industry standard PJLink™ protocol. Start the Projector-Control Device Installer.
Preparation/SetUp (continued) Setting the password (Password Setup) Enter “0” and press the Enter key. Input the old (current) password and press the Enter key. (Default password is admin.) If you input a wrong password, an error message • appears and the setting menu is displayed again. In this case, set the password again.
Setting the LAN control (LAN-Controlled Mode) Enter “3” and press the Enter key. To enable the e-mail notifi cation function of Projector- View, enter 1 and press the Enter key. (Default is OFF (0).) (See pages 12 - 15 for ProjectorView function.)
Preparation/SetUp (continued) Setting the PJLink™ certifi cation (PJLink certifi cation Mode) Enter “5” and press the Enter key. When you don’t use PJLink™ protocol • communication, skip this item. (See page 16 for PJLink™.) To enable the PJLink™ certifi cation, enter “1” and press the Enter key.
ProjectorView Using the ProjectorView This section describes ProjectorView, a tool to control and monitor the projector’s operations by a Web browser. The major functions of ProjectorView are: • Power on/off • Input source switching • State information indication (projector’s name, temperature, lamp operation time, error/alert, etc.) •...
Page 13
[Start] - [Control Panel] - [Java Plug-in] and disable the cache. [ProjectorView main screen] Failures in the projector are indicated with dots. When you place the mouse cursor to a dot, the indicated failure is described in the box at the bottom. (Note) When mute is on, you cannot change the lamp mode.
• Response may be delayed depending on the operating state of the projector. • The DHCP mode may not operate with certain devices (routers etc.). • When you turn on the projector by pressing the ON/OFF button on the ProjectorView main screen, other commands are not accepted for about 1 minute.
ProjectorView (continued) Initial setting To load information on the projector such as model name and lamp operating time, set the projector data in advance. Click the SETUP button on the ProjectorView main screen. The Projector Setup screen appears. Enter data according to the description of each setting item.
• This projector is fully compliant to the specifi cations of JBMIA PJLink™ Class 1. It supports all the commands defi ned by PJLink™ Class 1, and the compliance has been verifi ed with the PJLink™ standard specifi cations Version 1.0.
Page 17
• The operating time and temperature may not be displayed correctly. In this case, close the browser, recognize this projector using Projector-Control Device Installer, and then start the browser again. (Refer to “How to start up” of ProjectorView.) •...