Tv Back Panel - Mitsubishi Electric WD-60735 Owner's Manual

C series, 735 series, 736 series, 835 series dlp high-definition television
Hide thumbs Also See for WD-60735:
Table of Contents

Advertisement

8
1. Television Overview
Front-Panel Indicators
Off
Steady On
Slow Blinking
POWER/TIMER Indicator
LED Color TV Condition
TV is powered off.
None
TV is powered on.
Green
TV powered off, auto-on timer is set. Normal operation. TV can be turned on at any time.
Green
TV just plugged into AC outlet.
Green
AC just restored after power failure.
TV is rebooting after System
Reset used.
TV is rebooting after power
fluctuation or receiving abnor-
mal digital signals from a digital
channel or digital device.
You have begun the procedure
to update software from an
authorized flash memory device.
STATUS Indicator
LED Color TV Condition
Normal TV on or standby condition.
None
TV is too hot.
Yellow
TV may require service.
Red
LAMP Indicator
LED Color TV Condition
Normal TV on or standby condition.
None
TV just powered off and lamp is
Green
cooling.
1. Lamp access door is open or
Yellow
not secure.
2. No lamp installed.
Lamp no longer illuminates and has
Red
reached the end of the lamp life.
Fast Blinking
Additional Information
Normal operation.
Normal operation.
Wait approximately two minutes for blinking to stop before
turning on. Normal operation.
Additional Information
Normal operation.
The TV will display a warning message and shut off if it overheats.
• Ambient room temperature may be too high. Turn off the TV
and let the room temperature to drop.
• Clear blocked air vents. Ensure at least a four-inch clear-
ance on all sides of the TV.
• Clean the lamp-cartridge air filter. See Appendix E.
Turn off the TV and unplug the set from the AC power source.
Wait one minute and then plug the set back in. See Appendix D.
If the LED is still on, contact your dealer or a Mitsubishi Autho-
rized Service Center. Go to www.mitsubishi-tv.com or call
1-800-332-2119 to receive Authorized Service Center information.
Additional Information
Normal operation.
Starts to blink 60 seconds after turning off TV. TV can be turned
back on before blinking starts or after blinking stops, but not
while the indicator is blinking. Normal operation.
TV will not operate until lamp access door is secure. See
Appendix E for installation information.
TV will not operate without a lamp. See Appendix E for installa-
tion information.
Replace the lamp. The TV will not operate when the lamp no
longer illuminates. See Appendix E for installation information.

TV Back Panel

11
3D
GLASSES
EMITTER
10
9
AVR
AUDIO
OUTPUT
DVI/PC
INPUT
R
AUDIO
R
AUDIO
L
L
ANT 2 / AUX
Y
ANT 1 / MAIN
R
Y/ VIDEO
AUDIO
L
R
(480i / 480p / 720p / 1080i)
DIGITAL
AUDIO
OUTPUT
1
2
3
9
4
5
1. ANT 1/ANT 2 (Antenna)
If you are connecting an antenna or direct cable service
without a cable box, connect the main antenna or cable
source to ANT 1. Use ANT 2 for a second source.
ANT 1 and ANT 2 can each receive digital and analog
over-the-air channels from a VHF/UHF antenna or non-
scrambled digital/analog cable source.
2. AVR AUDIO OUTPUT
Use AVR AUDIO OUTPUT to send analog audio of the
program currently shown on the screen to an analog
A/V surround sound receiver or stereo system. Digital
audio from digital channels and HDMI devices is con-
verted to analog audio by the TV. This is the only audio
connection needed between it and the TV if using an
analog A/V receiver or stereo system.
3. DIGITAL AUDIO OUTPUT
This output sends Dolby Digital or PCM digital audio to
your digital A/V surround sound receiver. Analog audio
from analog channels and devices and HDMI devices is
converted by the TV to PCM digital audio. If you have
1. Television Overview
IR NetCommand Output/
External Controller Input
available on 736 and 835
4
8
series models.
HDMI
VIDEO: 480i/480p/720p/1080i/1080p
L
VIDEO
AUDIO: PCM STEREO
PC: VGA, W-VGA, SVGA, W-SVGA,
IR-
XGA, W-XGA, SXGA, 720p/ 1080p
NetCommand
R
Output / External
Controller Input
HDMI
Pb
Pr
1
2
Pr
Pb
S-VIDEO
INPUT 3
5
6
7
a digital A/V receiver, in most cases this is the only
audio connection needed between the TV and your A/V
receiver.
4. Composite Video (INPUT 1, INPUT 3)
Use the VIDEO jacks to connect a VCR, DVD player,
standard satellite receiver, or other A/V device to the
TV. Use the adjacent AUDIO R and L inputs for INPUT
1 or INPUT 3 if you wish to send audio to the TV. Note
that the INPUT 3 composite video jack is automatically
disabled when you connect to S-VIDEO (item 6).
5. Component Video (INPUT 1, INPUT 2)
Y Pb Pr Component Video (480i/480p/720p/1080i)
Use these jacks to connect devices with component
video outputs, such as DVD players, external HDTV
receivers, or compatible video game systems. Use the
adjacent AUDIO R and L jacks for INPUT 1 or INPUT 2
if you wish to send audio to the TV. See Appendix A
specifications for signal compatibility.
9
3

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Wd-65735Wd-65736Wd-65835Wd-73735Wd-73736Wd-73835 ... Show all

Table of Contents