Table of Contents
Advertisement
Quick Links
DIGITAL MONOCHROME PRINTER
MODEL
P91DW(UB)
OPERATION MANUAL
FUNC
DOWN
UP
SET
GAMMA
FEED
OPEN
THIS OPERATION MANUAL IS IMPORTANT
TO YOU.
PLEASE READ IT BEFORE USING YOUR
DIGITAL MONOCHROME PRINTER.
DIGITAL MONOCHROME
PRINTER
This digital monochrome printer complies with the requirements of the EC Directive
89/336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC.
The electro-magnetic susceptibility has been chosen at a level that gains proper
operation in residential areas, on business and light industrial premises and on small-
scale enterprises, inside as well as outside of the buildings. All places of operation are
characterised by their connection to the public low voltage power supply system.
COPY
Advertisement
Table of Contents
Related Manuals for Mitsubishi P91DW(UB)
Summary of Contents for Mitsubishi P91DW(UB)
- Page 1 DIGITAL MONOCHROME PRINTER. DIGITAL MONOCHROME PRINTER This digital monochrome printer complies with the requirements of the EC Directive 89/336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small- scale enterprises, inside as well as outside of the buildings.
- Page 2 FOR THE MODEL P91DW(UB) ONLY WARNING: In the USA or Canada, use the AC power cord according to the recommendations as below, in order to comply with UL2601-1 and CAN/CSA C22.2 No. 601.1. Case 1. Connect to the 120V receptacle of the room or the host equipment. The AC power cord should be UL or CSA approved and consist of type SJT, size 16 or 18AWG, length 2.5m or shorter cord with IEC320/C13 type, 125V 10A or higher rating connector and NEMA 5-15 type, 125V 10A or higher rating, Hospital...
- Page 3 CAUTION: RISK OF ELECTRIC SHOCK TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
-
Page 4: Table Of Contents
CONTENTS 1 1 1 1 1 CONTENTS ... 1 2 2 2 2 2 PRECAUTIONS ... 2 - 4 3 3 3 3 3 UNPACKING ... 5 4 4 4 4 4 FEATURES AND FUNCTIONS Front Panel ... 6 Rear Panel ... 7 5 5 5 5 5 INSTALLATION OF PAPER ... -
Page 5: Precautions
In the interest of safety, please observe the following pre- cautions: POWER REQUIREMENT This Digital monochrome printer is designed for opera- tion on 120/220-240V AC 50/60Hz in U.S.A and Canada, 220-240V AC 50/60Hz in Europe. Never connect to any outlet or power supply having a different voltage or fre- PROTECTIVE MEASURES IF ABNORMALITIES ARISE, . -
Page 6: Thermal Paper
CONNECTION DEVICES Read thoroughly "Operating Precautions" of the instruc- tion booklets for other devices connected with the Digital monochrome printer. Do not disconnect the power cord during printing. CAUTION ON RELOCATING When transporting this unit, make sure it is not likely to be subjected to impacts. - Page 7 SAFETY TECHNICAL CHECKS Periods: According to the recommendations of the manufacturer of medical device. Scope: a) Visual check Housing, cables, operator controls, readout device ( displays, LED etc.), labels, accessories, instruction manual. b) Function test Performance check acc. instruction manual, also unity and applicability of set and accessory test. c) Electrical check Safety electrical test of the configuration in accordance with EN60601-1.
-
Page 8: Unpacking
3 3 3 3 3 Take the unit out of the box carefully. 4 4 4 4 4 Unwrap the unit. AC power cord Cleaning paper Operation manual Printer driver (1 floppy disk) • Make sure to keep the unit horizontal. -
Page 9: Features And Functions
FEATURES AND FUNCTIONS Front Panel 1 2 3 4 5 6 FUNC OPEN Name Power switch FUNC button DOWN button UP button SET button Indicator GAMMA button FEED button COPY button Print exit/Cutter Lever COPY DOWN GAMMA FEED Function Turns on/off the power. Function mode changes whenever FUNC is pressed. -
Page 10: Rear Panel
Rear Panel 1 2 3 4 LOCK 1 2 3 4 Name Mode switches USB terminal Power terminal (AC LINE) Potential equalization terminal Makes the connected equipment of AC LINE POTENTIAL EQUALIZATION TERMINAL This is used to equalize the potential of the equipment connected to this unit. -
Page 11: Installation Of Paper
“OPEN” position. The door opens. 2 2 2 2 2 Load the paper roll. •Place the paper roll in the printer. INCORRECT CORRECT Note: The printing surface is the outside. Place the paper with the thermo- sensitive side (printing side) up. - Page 12 When setting the paper, observe the following precautions to prevent paper jam. Do not use defective paper. Adjust the paper position correctly. Do not slack the roll paper. If the side of the print paper is uneven or the core is sticking out, the amount of paper feeding after printing may vary.
-
Page 13: Example Of Connection
Printer driver is required to print the data from a personal computer connected with this printer. The printer driver for Windows Refer to the “Read me” for installing the printer driver in the floppy disk supplied with this unit. 2 2 2 2 2... -
Page 14: Printing
PRINTING Printing procedure 1 1 1 1 1 Turn on the power. 2 2 2 2 2 Print a picture displayed on the screen. • Print a picture with an application software. The image data is transferred through parallel data interface. Copy printing You can set the number of copies by pressing the COPY button on the front... - Page 15 Precautions on Printing If printing is continued with a very black picture, the printer will become overheated and printing will not be available. " In this case, wait for a while until the unit is cooled down.
-
Page 16: Adjustment Of Print Picture
ADJUSTMENT OF PRINT PICTURE Selection of Gamma (γ) Curve You can select γ-curve by pressing the gamma button " ". Each time the button is pressed, the indicator and γ-curve number is switched. After a γ-curve number has been selected, press the "SET" button to store the γ-curve number. Indicator/Adjustable Item γ−curve set mode... -
Page 17: Setting Of Function Mode
SETTING OF FUNCTION MODE Select a function mode by pressing the FUNC button. FUNC • Each time the FUNC button is pressed, the mode is switched as shown below. Standby Paper type selection mode Paper saving mode Set condition printing mode Buzzer set mode DOWN GAMMA... - Page 18 Mode to select paper saving mode. : Paper saving mode OFF : Paper saving mode ON Mode to select whether the printer conditions will be printed over the image or not. : The printer conditions are not printed. : The printer conditions are printed.
-
Page 19: Error Display
ERROR DISPLAY When an error in operation occurs, an audible alarm and a visible error is displayed in the LED indicator. Cause/Error display 1 1 1 1 1 [Symptom] No paper • When the paper runs out or the paper is not installed, printing becomes impossible and alarm tone is given. - Page 20 Cause/Error display 4 4 4 4 4 Door error [Symptom] • When the door opens, an alarm tone is given. [Remedy] Close the door. Cause/Error display 5 5 5 5 5 [Symptom] Gear lock error • When the thermal head does not automatically go up after printing, an alarm tone is given.
-
Page 21: Status And Modes
STATUS AND MODES Set state/Mode Power off Stand-by Print state Copy state γ-curve set mode (γ-curve) Paper type setting mode Paper saving mode Set condition printing mode Buzzer setting mode Error detect state LED display Contents of right Point and side LED display Left right... -
Page 22: Use Of Cleaning Paper
USE OF CLEANING PAPER When the thermal head is dirty with dust and perspiration, etc., white spots or stripes may appear on the print. In this case, clean the thermal head in the following procedure BY USING THE SUPPLIED CLEANING PAPER. 1 1 1 1 1 Turn on the power. -
Page 23: Maintenance
MAINTENANCE Turn off the power for maintenance. Wipe off stains of the front panel with a soft cloth. When the panel is heavily stained, wipe of with the cloth moistened with neutral cleanser diluted by water and finish with a dry cloth. When the rubber roller is dirty with dust, etc., a black spot may appear on the print. -
Page 24: Specifications
6.1" x 3.8" x 11.8" (154mm x 97mm x 300mm); W x H x D 6.8 lbs (3.1kg) AC power cord ... 1 piece Thermal paper KP65HM-CE ... 1 roll Cleaning paper ... 1 sheet Printer driver ... 1 floppy disk Thermal paper KP65HM-CE, KP65H-CE, KP61B-CE, KP61S-CE, KP91HG-CE... - Page 25 MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. 9351 Jeronimo Road, Irvine, CA 92618 Phone 949-465-6000 Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Herts. AL10 8XB, England, U.K. Phone (0) 1707 276100 German Branch Gothaer Strasse 8, 40880 Ratingen ; Postfach 1548, 40835 Ratingen ; Germany Phone (2102) 486-9250 French Branch 25, Boulevard des Bouvets - 92741 NANTERRE cedex...