1. Manuals
  2. Brands
  3. Mitsubishi Manuals
  4. Security Camera
  5. DIS710E
  6. Operation manual

Mitsubishi DIS710E Operation Manual

Mitsubishi operation manual id photo system dis710e
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ID PHOTO SYSTEM
DIS710E
OPERATION MANUAL
POWER
OPEN
REMOTE

Advertisement

Table of Contents
loading

Related Manuals for Mitsubishi DIS710E

Summary of Contents for Mitsubishi DIS710E

  • Page 1 ID PHOTO SYSTEM DIS710E OPERATION MANUAL POWER OPEN REMOTE...

  • Page 2: Table Of Contents

    The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system. CONTENTS PRINT •...

  • Page 3: Safety Precautions

    In the interest of safety, please observe the following precautions: POWER REQUIREMENT This system is designed for operation on 220V-240V, 50Hz AC. Never connect to any outlet or power supply having a different voltage or frequency. WARNNG: THIS APPARATUS MUST BE EARTHED.
  • Page 4 BE CAREFUL WITH THE PRINTING UNIT Don't move the unit while the printing unit is sliding out. This may cause injury. Be careful not to catch your finger in the printing unit while the printing unit is being retracted into the unit. CONNECTION CABLES Use the cables provided INSTALLATION LOCATIONS...

  • Page 5: Connecting Devices

    CAUTION ON RELOCATING When transporting this unit, make sure it is not likely to be subjected to impacts. They can be a prime cause for damage. Further, make sure to disconnect the power cord from the power outlet, and the cables from the connected devices.

  • Page 6: Unpacking

    2. UNPACKING Take the unit out of the box by the following procedures. Make sure to check the contents. 2 2 2 2 2 PRINTER 1 1 1 1 1 Open the top of the box. 2 2 2 2 2 Remove the accessory box.

  • Page 7: Printer Setup

    3. PRINTER SETUP Before printing a photo, install a print paper and ink cassette. REMOVING SCREW AND CUSHION See CP710E operation manual for details. 2 2 2 2 2 1 1 1 1 1 REMOVING SCREW Remove the screw at the bottom of printing unit with a screwdriver or coin.
  • Page 8 2 2 2 2 2 Insert the print paper in the position as shown right. Place the gear to the right side. Set the paper roll first on the right side paper holder. Then, set the paper roll on the left side paper holder. 3 3 3 3 3 Insert the print paper between roller 4 4 4 4 4...
  • Page 9 INSTALLING THE INK SHEET Install the ink cassette with the ink sheet rolls before inserting the ink cassette into the printer. 1 1 1 1 1 Put the coloured roller of the ink sheet to the ink cassette. B B B B B 2 2 2 2 2 Put the thin stick of white roller to the ink cassette.

  • Page 10: Connection

    4. CONNECTION Connect the components as follows.(example) Make sure to turn off each device when connecting. If you wish to fix the connection box to the printer, set them first before connecting with cables. CABLE CONNECTION Strobe (option) To S-VIDEO IN Transport screw (when fixing to the printer)

  • Page 11: Connection

    There are two ways to set connection box. FIXING TO THE PRINTER 1 1 1 1 1 Loosen three screws on the back of the printer. 2 2 2 2 2 Catch the hooks of the connection box on each screws on the printer.

  • Page 12: Taking The First Picture

    5. TAKING THE FIRST PICTURE You can take a picture twice, and choose the better one. 1 1 1 1 1 Turn on the power of this system. Make sure to turn on the power of the connection box first. Then, turn on the power of the camera and the printer.
  • Page 13 8 8 8 8 8 Press MEM button to transfer the image to the printer. The image is memorized in the printer. 9 9 9 9 9 Press SHOT button to display the source image. A A A A A Press SHOT button again.

  • Page 14: Picture Quality Adjustment

    6. PICTURE QUALITY ADJUSTMENT ADJUSTING PICTURE QUALITY To adjust the image source first is the key to get maximum picture quality. 2 2 2 2 2 CAMERA ADJUSTMENT Always adjust the camera setting first. Only after you are sure that the camera is providing the best picture quality and colour balance, adjust the printer setting.
  • Page 15 7 7 7 7 7 Press SHOT button to take a picture. Check the brightness of image. If the brightness is not improved, repeat the steps get the best setting. 2 2 2 2 2 ADJUSTING THE COLOUR OF IMAGE (WHITE BALANCE) Default setting is flash light W.B.
  • Page 16 6 6 6 6 6 Press ZOOM button to finish the white balance setting menu. 2 2 2 2 2 FINE-ADJUSTING OF COLOUR When more colour adjustment is necessary after adjusting white balance, use a remote control of the printer. 1 1 1 1 1 Connect the remote control to the printer or the camera.

  • Page 17: Features And Functions

    7. FEATURES AND FUNCTIONS 3 3 3 3 3 2 2 2 2 2 1 1 1 1 1 7 7 7 7 7 1 1 1 1 1 D D D D D C C C C C B B B B B A A A A A IRIS 9 9 9 9 9 MENU...
  • Page 18 8 8 8 8 8 UP BUTTON, SET BUTTON, DOWN BUTTON On ZOOM mode: Use to adjust zoom. Press UP to zoom up (TELE) and DOWN to zoom back (WIDE). On IRIS mode: Use to switch iris between auto and manual.

  • Page 19: Advanced Setting

    8. ADVANCED SETTING You can print 1, 2, 4, 6 and 16-image on a sheet. To make 1 and 16-image print, change the setting as follows. 2 2 2 2 2 PRINTING 16- OR ONE-IMAGE ON A SHEET Use the remote control of the printer to print 16-image on a sheet.
  • Page 20 2 2 2 2 2 LOCK FUNCTION To avoid changing the setting of the camera, locking the camera setting is recommended. When locked, the switch is on the right side and “L” is shown on red. When unlocked, the switch is on the left side and “U” is shown on green.
  • Page 21 THE BEST CONDITION FOR THIS SYSTEM 0.3m 2 2 2 2 2 EFFECT OF BACK FLASH • The back flash reduces the shadow behind the subject. Without back flash 0.3m 1.5m to 2m With back flash POWER OPEN REMOTE...

  • Page 22: Troubleshooting

    9. TROUBLESHOOTING BEFORE CALLING FOR SERVICE Use the following troubleshooting chart to resolve any apparent defect in operation. If you are unable to resolve the problem, unplug the power cord and contact your dealer. Causes No power No signal Image is not printed. The camera setting does not work.

  • Page 23: Specifications

    Guide sheet (3) Print paper Ink sheet Connection box Output terminal Composite video PAL RS-232C Mini DIN (camera control) Power supply AC 220-240V, 50Hz Power consumption 0.6A (Inrush current 1.2A) Installation conditions Temperature External dimensions 214mm(W) x 85mm(H) x 110mm(D)
  • Page 24 Name of Importers Mitsubishi Electric Europe B.V. Benelux Branch Nijverheidsweg 23 A, 3641 RP. Postbus 222, 3640 AE Mijdrecht Phone 02972-82461 French Branch 25, Boulevard des Bouvets - 92741 NANTERRE cedex Phone (01) 55.68.55.00 German Branch Gothaer Strasse 8, Postfach 1548, 40880 Ratingen 1, Germany Phone (02102) 4860 Irish Branch Westgate Business Park, Ballymount, Dublin 22, Ireland...

Table of Contents