CONTENTS PRODUCT IDENTIFICATION INFORMATION SIGNALING LAMPS CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE ACCESSORIES SUPPLIED WITH THE UNIT WITH THE EUROPEAN INSTALLATION DIRECTIVE 2002/96/EC BEFORE USING THE APPLIANCE At the end of its working life this USING THE REMOTE CONTROL UNIT equipment must not be disposed of as an household waste.
PRODUCT IDENTIFICATION 1. Wireless remote control unit 2. Signaling lamps 3. Supply air deflector 4. Lateral air intake grilles 5. Front air intake grille 6. Air filter 7. Electric cable with plug 8. Air inlet hole 9. Air outlet fan 10.
ACCESSORIES SUPPLIED WITH THE UNIT 1. PLASTIC TUBE (1pcs.) 2. EXTERNAL GRILLES (2pcs.) 3. INTERNAL GRILLES (2pcs.) 4. TENSION BARS (2pcs.) 5. FULL SCALE DIAGRAM (1pcs.) 6. RAWL PLUGS + SCREWS (15pcs.) 7. REMOTE CONTROL UNIT (1pcs.) 8. BATTERIES FOR REMOTE CONTROL (2pcs.) INSTALLATION The installation should be carried out by a qualified installer, following the instructions as shown.
Page 5
- Insert in the two holes the supplied plastic tube; cut it at the right length: it is necessary to measure the thickness of the wall and subtract 70 mm. OUTSIDE - Fix the two anti-intrusion grilles and the two external grilles INSIDE with the blades toward the bottom using wall rawl plugs and screws.
Page 6
WARNING! The supplied plastic conduits can be used for Plastic tubes ø 160mm wall thickness up to 50 cm; in special cases (i.e. installations Insulation in a garret) it can be necessary to utilise longer tubes. The maximum allowable length is 2 m. You can go to any building material retailer, buy the plastic tube of the same diameter (ø160 mm), of the proper length and cover it outside with insulating material (thickness: about 3-4 cm).
BEFORE USING THE APPLIANCE Check that the power supply at the location where the air conditioner is going to be used is 220-240V ~ 50Hz . ● Make sure that the electrical installation is suitable to supply continuously current necessary for the air conditioner in ●...
TEMPERATURE SENSOR SELECTOR USING THE REMOTE CONTROL UNIT Under normal conditions the room temperature is detected ● and checked by the temperature sensor placed in the HOW TO INSTALL BATTERIES remote controller (I FEEL icon displayed ).This function Remove trhe lid in the rear part of the remote control unit ●...
REMOTE CONTROL UNIT DISPLAY Information is displayed when the remote controller is switched on. If switched off, only the operating mode, the room temperature and the clock are shown I FEEL mode is active (remote controller Operation mode Room sensor active) temperature Automatic Displayed when...
HOW TO SET THE PRESENT TIME HEATING PERFORMANCE A heat pump conditioner heats a room by taking heat from 1. Press the button SEL TYPE three times. outside air. The heating efficiency will fall off when the The time indication alone flashes. outdoor temperature is very low.
NOTE NIGHT MODE Use DRY operation when you want to reduce the humidity ● The NIGHT mode enables you to save energy. ● in the room. 1. Set the MODE selector to cool, dry or heat. ● Once the room temperature reaches the set level, the unit 2.
SETTING THE TIMER ADJUSTING THE AIR FLOW DIRECTION A) HOW TO SET THE ON TIME HORIZONTAL (manual) The horizontal air flow can be adjusted by moving the vertical 1. Press the SEL TYPE button once. vanes to the left or right, as indicated in the following figures. The ON and time indications flash.
OPERATION WITHOUT THE REMOTE WARNING CONTROL UNIT The use of portable telephones near the air conditioner • If you have lost the remote control unit or it has troubles, may cause disturbance to its normal operation and must follow the steps below. be avoided.
Page 14
Trouble: Operation lamp (4) flashes, the fan operates, Trouble: Clicking sound is heard from the air conditioner. while the compressor stops. Possible cause: Possible cause: 1. During operation, any plastic parts may expand or shrink 1. Safety float switch operating due to excessive due to a sudden temperature change.
BOYLER CONNECTION KIT (ONLY FOR 245C-235H MODELS) The unit is predisposed to replace a radiator in an already existing heating system. it is necessary to buy the boyler connection kit that can be installed on both side of the unit according of the position of the water connections. CARE AND CLEANING WARNING! For safety’s sake, be sure to turn the air conditioner Intake grille...
Page 16
In order to carry on a constant improvement, our products can be modified without prior notice. Per garantire un costante miglioramento dei nostri prodotti, ci riserviamo di modificarli senza preavviso. Par souci d’amélioration constante, nos produits peuvent être modifiés sans préavis. Unsere Produkte werden laufend verbessert und können Vorankündigung abgeändert Werden.