Channelview™ Channel Listings - Mitsubishi Electric LT-40133 Owner's Manual

Remote Control, continued
Record/Playback Keys
Use any of these methods to enable the recording and
playback commands:
• Program the remote control for your DVR, VCR, or
DVD player/recorder and set the slide switch to VCR,
DVD, CABLE/SAT, or AUDIO as appropriate.
• On LT-40134, LT-46144, and LT-52144 model TVs:
Perform NetCommand IR "learning" for the device.
• Check HDMI devices for compatibility with the TV's
NetCommand for HDMI feature (see below).
23. (PAUSE): Pauses a VCR, DVR, or DVD. See pre-
vious page for use during TV viewing.
24. (PLAY): Plays a VCR, DVR, or DVD.
25. (RECORD): Records with a VCR or DVR.
26. (STOP): Stops play of a VCR, DVR, or DVD.
27. (REVERSE): Rewinds a VCR. Reverse scans a
DVR or DVD.
28. (FORWARD): Fast forwards a VCR. Forward
scans a DVR or DVD.
Note: To operate other audio/video devices:
• See Appendix D, "Programming the Remote
Control."
• See chapter 6, "NetCommand," for NetCommand
IR "Learning" of device keys.
• For HDMI devices compatible with the TV's
NetCommand for HDMI feature, see below.
NetCommand for HDMI Devices
The TV's remote may operate some functions of
compatible HDMI devices able to receive commands
through the HDMI cable. Test your equipment with the
TV's remote to find out which commands are sup-
ported. See below for commands that may be avail-
able, depending on the individual device.
Note: On models LT-40134, LT-46144, and LT-52144,
you can add commands using NetCommand IR "Learn-
ing" after connecting and placing IR emitters for the
devices.
Press PLAY on the device itself to:
• Turn on the TV if not already on
• Switch to the device (no need to display the Input
Selection menu)
• Begin play of the device
VCR, DVD, and DVR functions that may be available:
Record/ Menu
Playback Navigation
ENTER
—
CANCEL (to cancel)
Channel Tuning Other
CH/PAGE GUIDE
/
—
F1 (content)
Digits 0–9,
CANCEL
ENTER MENU
4. TV Operation and Features
Resetting the Remote Control
If the slide switch is set to TV and the TV does not
respond properly, reset the remote control.
1. Press and hold POWER for several seconds until the
button blinks twice and goes off.
2. Release the POWER button.
3. Press keys 0 0 9 3 5 and the POWER button will blink
twice when you finish entering the code. While
entering the code, pause for a moment between
each key press to ensure it is recognized.
Care of the Remote Control
• Use only alkaline batteries (never use old & new
batteries together).
•
Be within 20 feet of the equipment.
• Do not press two or more buttons at the same time
unless instructed to do so.
• Do not allow unit to get wet or become heated.
• Avoid dropping on hard surfaces.
•
Do not use harsh chemicals to clean. Use only a
soft, lightly moistened cloth.
ChannelView™ Channel Listings
ChannelView (or TV Guide Daily, if active - model
LT-40134 only) channel listings are accessible via the
GUIDE key. For TV Guide Daily details, see Appendix C.
ChannelView displays only digital channel names and
program information as sent by broadcasters or local
cable providers and may be incomplete.
To receive ChannelView/TV Guide updates, keep
Energy Mode set to Fast Power On, set TV Clock, and
leave the TV powered off for a while each day. Note:
Digital channel listings are updated while viewing.
Using ChannelView
Feature
See ChannelView listings
from ANT 1 or ANT 2.
Close ChannelView
Scan channels one by one. Press & hold
Scan channels quickly.
Jump to listings for a spe-
cific channel.
See more of the program
description.
Move navigation to the
program guide.
Move navigation to the
channel guide.
Tune to the highlighted
channel.
29
Press Key
Press GUIDE.
Press GUIDE or EXIT.
or .
Press & hold CH/PAGE
/
1. Enter the channel
number (see numbers
in upper left).
2. Press ENTER.
Press INFO.
Press .
Press .
Press ENTER.
.