Lan (Communication) Setting - Mitsubishi Electric DX-TL4516U Installer Manual

LAN (Communication) Setting

This item is used to make the communication settings
between this unit and the PC connected to LAN terminal.
System Menu
1 COM/LAN
3 LAN (Communication) Setting
1 LAN Address Setting
2 Service Port Setting
E-mail Notification Information
3
D E-mail Notification Detailed Information
IP Alarm Notification Information
4
D Alarm Notification Detailed Information
[LAN Address Setting]
1. Set the IP address, sub net mask, and Gateway.
step
• MAC address is shown on the bottom of the
screen of <LAN (Communication) Setting>.
D o n o t a s s i g n " 0 0 0 . 0 0 0 . 0 0 0 . 0 0 0 " t o I P a d d r e s s
and broadcast address. If this address is assigned,
communications or any other functions of this unit may
not be performed correctly.
The setting cannot be changed during recording. Stop
recording before changing the setting.
[Service Port Setting]
2. Set the port setting of "Web," "User Access," and
step
"Administrator."
• This item is used to set the port number which is
necessary to connect with PC.
• Normally, leave the setting as is.
Do not change the setting without sufficient knowledge
about the network setting.
When making the settings other than communication port
settings of "Web," "User Access," and "Administrator,"
using the supplied application software, DX-PC55U, is
required. Refer to the operation manual of the application
software.
[E-mail Notification Information]
3. C h e c k t h e s e t ti n g s o f " E - M a i l A d d r e s s " a n d
step
"Recorder ID."
• When selecting "Mail," the e-mail is sent for the
selected address.
Using the web function of this unit is required to input
"E-Mail Address" and "Recorder ID."
[E-mail Notification Detailed Information]
4. Check the contents to be transmitted to the PC.
step
Remain: Transmits signal when the remaining
capacity reaches the value set for Call out setting.
Temp/Fan: Transmits signal when the high
temperature is detected or the fan is stopped.
Reboot: Transmits signal when the unit is
rebooted.
Record: Transmits signal when the recording is
started.
7
step
Alarm: Transmits signal when the alarm recording
is started.
Sensor: Transmits signal when the signal is input
1
step
to the terminal on the rear panel.
Using the web function of this unit is required to change
the contents to be transmitted.
2
step
[IP Alarm Notification Information]
5. Check the settings of "IP Address" and "Target Port."
step
3
step
• This item is used to transmit warning signals or
signals of status change such as a closure of a
rear terminal to the PC connected.
4
step
• When selecting "Test," the sending test for the
set IP address and port is executed.
Using the supplied application software, DX-PC55U, is
5
step
required to change the IP address and target port. Refer
to the operation manual of the application software.
6
Transmission of signal to broadcast address is not
step
supported.
[Alarm Notification Detailed Information]
6. Check the contents to be transmitted to the PC.
step
Remain: Transmits signal when the remaining
capacity reaches the value set for Call out setting.
Temp/Fan: Transmits signal when the high
temperature is detected or the fan is stopped.
Reboot: Transmits signal when the unit is
rebooted.
Record: Transmits signal when the recording is
started.
Alarm: Transmits signal when the alarm recording
is started.
Sensor: Transmits signal when the signal is input
to the terminal on the rear panel.
Using the supplied application software, DX-PC55U, is
required to change the contents to be transmitted. Refer
to the operation manual of the application software.
7. S e l e c t " R e t u r n " i n t h e s c r e e n o f < L A N
step
(Communication) Setting>.
• When the setting of "IP Address," "Sub Net
Mask," "Gateway," or "Service Port Setting" is
changed, the power turns off automatically and
then the unit restarts.
Operations
71