Information/Service; Hdd Information; Warning Log List; Reset To Factory Settings - Mitsubishi Electric DX-NT400E Installation And Operation Manual

<INITIAL SET UP/INFORMATION> (continued)

INFORMATION/SERVICE

This menu is used to check the log list or list of power
failures, etc., and to initialize the menus.
At the bottom of the screen, the following information
appears.
• The accumulated operation time since the beginning of
usage ("ELAPSED TIME")
• The HDD setting of MIRRORING, PARTITION, or
NORMAL mode ("HDD SETTING" and "PARTITION SIZE")
<INFORMATION/SERVICE>
>>HDD INFORMATION

WARNING LOG LIST

RESET TO FACTORY SETTINGS

MAIN HDD DATA CLEAR
SUB HDD DATA CLEAR
ELAPSED TIME:
HDD SETTING
PARTITION SIZE
"SUB HDD DATA CLEAR" and "PARTITION
SIZE" appear when "HDD SETTING" in <INITIALI-
ZATION> screen is set to "PARTITION."

HDD INFORMATION

This menu is used to check the recorded range of the HDD.
<HDD INFORMATION>
A: HDD(120GB)
B: HDD(120GB)
MAIN START 02-02-2003 00:00:00
SUB
Recording start and end times of "SUB" HDD
appear when "HDD SETTING" in <INITIALIZATION>
screen is set to "PARTITION."
1. (To check the recorded range of the HDD • • • )
Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select "HDD INFORMATION" in the
<INFORMATION/SERVICE> screen. Display the desired
setting and determine such setting.
2. Press the CLEAR button or the SET UP button.
WARNING LOG LIST
This menu is used to check the number, date, time, and
type of failures.
<WARNING LOG LIST>
NO DATE
>>0003 04-03-03 15:03:27 P-LOSS
0002 26-02-03 09:56:43 ALM ON
0001 02-02-03 10:00:00 ALM OFF
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
54
6H
PARTITION
10%
END 04-04-2003 00:00:00
START 02-02-2003 00:00:00
END 04-04-2003 00:00:00
TIME WARNING
The failures displayed in the WARNING LOG LIST: (
see page 81).
"P-LOSS": Power failure.
"SYS RST": Reset button is pressed and the unit is
reset.
"ALM OFF": ALARM INTERRUPT button is pressed
and the unit is put on interruption.
"ALM ON": Alarm interrupt is cancelled manually by
pressing ALARM INTERRUPT button. Alarm
interrupt is cancelled automatically after 5 minutes
from the start of interruption.
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select "WARNING LOG LIST" in the
<INFORMATION/SERVICE> screen. Press the ENTER button.
• The <WARNING LOG LIST> screen appears.
• The WARNING LOG LIST displays up to 1000 items. When
the number of items exceeds this limit, the latest 1000 items
are displayed.
• JOG button : Selection moves to the next number.
• JOG button : Selection moves to the previous number.
• JOG button : Displays the page with date prior to the
date of the currently opened page.
• JOG button : Displays the page with date newer than the
date of the currently opened page.
When a failure occurs while the <WARNING LOG
LIST> screen is displayed, exit the screen and display
the screen again. A new item will be added to the list.
2. Press the CLEAR button or the SET UP button.
RESET TO FACTORY SETTINGS
This menu is used to initialize menu screen settings.
<RESET TO FACTORY SETTINGS>
>>EXECUTE
ENTER:EXECUTE,CLEAR:CANCEL
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select "RESET TO FACTORY
SETTINGS" in the <INFORMATION/SERVICE> screen. Press
the ENTER button.
• The <RESET TO FACTORY SETTINGS> screen appears.
• When cancelling the intialization of the menu screen
settings, press the CLEAR button.
2. Press the ENTER button.
• The menu screen settings are initialized.
3. Press the CLEAR button or the SET UP button.
The setting of present time, password, and timer
program are not reset.
When you execute RESET TO FACTORY
SETTINGS with the setting of IP ADDRESS, SUB NET
MASK, GATEWAY, SERVICE PORT SETTING in
<ETHERNET> screen or IP ADDRESS, TARGET,
OWN in <ALARM NOTIFICATION SETTING> screen
changed, the power turns off and the unit boots-up.