eka KF 912 Use And Instruction Manual page 6

_ TECNOEKA Srl _________________________________________________________ use and instruction manual _
- make sure that after inserting the power supply cord into the terminal block it does not
come into contact with any of the cooking range's hot parts.
- if the supply cable is damaged then it must be replaced by the manufacturer or by your if the supply cable is damaged then it must be replaced by the manufacturer or by your if the supply cable is damaged then it must be replaced by the manufacturer or by your if the supply cable is damaged then it must be replaced by the manufacturer or by your
technical support or by a qualified person to avoid any risk. technical support or by a qualified person to avoid any risk.
technical support or by a qualified person to avoid any risk. technical support or by a qualified person to avoid any risk.
Connection to the water mains - The appliance must be fed with softened drinking water, Connection to the water mains
Connection to the water mains Connection to the water mains
with hardness from 0.5°F to 5°F (it is obligatory to use a softener to reduce the formation of lime
inside the cooking chamber) and pressure in the range from 150 to 250 kPa (1.5 - 2.5 bar).
Connection to the water mains should be made through the threaded 3/4" solenoid-valve on
the rear (on the bottom) of the appliance, fitting in between a mechanical filter and an on/off tap
(before you connect the filter, allow a certain quantity of water to flow out in order to drain any
waste from the pipe).
Connecting the power cable - To access the terminal board, just remove the appliance's rear Connecting the power cable
Connecting the power cable Connecting the power cable
side-panel. Loosen the cable gripper and allow the cable to pass through it. Arrange the
conductors so that the earth conductor is the last to detach from its terminal if the cable goes
into a state of faulty traction. Connect the phase
"L2", connecting the neutral "L2"
"L2" "L2"
the terminal marked with the symbol
(this electrical connection lay-out is located near the power supply terminal board ). Tighten the
cable gripper and re-fit the rear side-panel of the appliance.
The appliance must be connected to an equipotential system
checked according to current legal regulations.
This connection must be made between different appliances by using the appropriate terminal
marked with the symbol
2
mm The equipotential terminal is at the rear of the appliance.
Safety thermal breaker Safety thermal brea
Safety thermal brea Safety thermal brea
against excessive dangerous over-temperatures which could be accidentally generated inside the
appliance. This device is located on the back of the oven.
5. 5. 5. 5. Use instructions (for Use instructions (for the user) Use instructions (for Use instructions (for
This appliance is not intended for use by persons (including children) with reduced phycal,
sensory or mental capabilities, or lack of experience and knowledge. Unless they have beengiven
supervision or instruction concerning use of appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
For first use, we advise you to let the appliance to run load-free at maximum temperature for
about one hour. In this way, any unpleasant smells due to thermal insulation and residual work
grease are eliminated.
This appliance must be used solely for the purpose for which it was expressly designed, i.e.
cooking foods in the oven. Any other use is considered unsuitable.
The appliance can be used: for all oven cooking of deserts, pizzas, meat, fish, vegetables, as
well as for gratinating, and for re-conditioning cooled and frozen foods.
When placing food in the cooking compartment, leave a space of at least 40 mm between
pans in order not to over-obstruct air circulation.
_ page 6 _________________________________________________________________________________________
neutral conductor to the terminal marked "N"
neutral neutral
according to the following lay-out:
. The equipotential conductor must have a minimum diameter of 2,5
ker - The appliance has a manually reset safety thermal breaker. It protects
ker ker
the user) the user) the user)
phase conductors to the terminals marked "L1" phase phase
equipotential system whose efficiency must first be equipotential system equipotential system
"N" and the earth earth conductor to
"N" "N" earth earth
"L1" and "L1" "L1"