[Video] Setting Video Size, Quality And Frame Rate - Canon VB-S30D Operating Manual

[Video] Setting Video Size, Quality and Frame Rate

The following can be set here.
• All Videos
Specify the set of video sizes used by the camera.
• JPEG
Set the video quality, size, maximum frame rate
and upload size in JPEG.
• H.264
Set the bit rate, video size and capture frame rate
in H.264.
• On-screen display
Set time, character string, etc. displayed over
video.
All Videos
(1) [Video Size Set]
Select the set of video sizes used by the camera from
[1920 x 1080 / 960 x 540 / 480 x 270], [1280 x 720 / 640
x 360 / 320 x 180], or [1280 x 960 / 640 x 480 / 320 x 240].
Select from [1280 x 720 / 640 x 360 / 320 x 180] or
[1280 x 960 / 640 x 480 / 320 x 240] for the VB-S805D
and VB-S905F.
All options in the [Video] menu and the size set that can
be selected in [Video Size] are determined by the set
selected here.
[Video Size Set]
[1920 x 1080 / 960 x 540 /
480 x 270]
[1280 x 720 / 640 x 360 /
320 x 180]
[1280 x 960 / 640 x 480 /
320 x 240]
Important
• Changing the [Video Size Set] setting will disconnect all
connections and then change all the video sizes.
Consequently, users connected to the camera must
reconnect.
• If the [Video Size Set] selection is changed and you click
[Apply and Reboot], review the following settings and check
the operation.
- Privacy mask settings
- View restriction settings
- Preset settings
- Intelligent function settings
- Camera Angle
• [1920 x 1080 / 960 x 540 / 480 x 270] cannot be selected for
the VB-S805D and VB-S905F.
50
Category Aspect ratio
1080p 16:9
720p 16:9
4:3 4:3
JPEG
(1) [Video Quality]
Select a desired video quality from 1 to 5 (5 levels) for
videos transmitted at each video size in JPEG.
Greater values have higher quality.
(2) [Video Quality: Digital PTZ]
Select a desired video quality from 1 to 5 (5 levels) for
Digital PTZ.
Greater values have higher quality.
(3) [Video Size: video Transmission]
Select the size of the transmitted video. The video
sizes that can be selected depend on the [Video Size
Set] setting. This becomes the start-up video size
used by each viewer if no video size has been set.
(4) [Maximum Frame Rate: Video Transmission]
Limit the maximum transmission frame rate per
second to reduce the viewer load. The maximum is 30
frames/sec. Enter a value of between 0.1 and 30.0.
(5) [Video Size: Upload / Memory card]
Select the size of video when using the upload
function (p. 55) or when recording to a memory card
(p. 73). The video sizes that can be selected depend
on the [Video Size Set] setting. Use [Event] > [Video
Record Action] (p. 60) to specify the destination of a
video recording (upload or memory card recording).
H.264(1)
Configure settings using H.264(1) when using H.264
video for upload or memory card recording. H.264(2)
video cannot be used for upload or memory card
recording.
H.264(1) video can be displayed using Admin Viewer and
RM-Lite Viewer. It cannot be displayed using VB Viewer.
(1) [Video Size]
Select the size of the transmitted video. The video
sizes that can be selected depend on the [Video Size
Set] setting.