Milwaukee 54-06-2800 Service Parts List

FIG. PART NO. DESCRIPTION OF PART
1 02-04-0640 Ball Bearing
2 02-04-0645 Ball Bearing
3 02-04-0852 Ball Bearing
4 02-04-1229 Ball Bearing
5 02-50-1611 Needle Bearing
6 02-50-2400 Needle Bearing
7 06-82-7275 7-18 x 3/4 Slotted Plastite T-20
8 12-99-2565 Service Nameplate
9 16-10-2215 Armature
10 18-07-2200 Field
11 22-18-1210 Brush Card Assembly
12 22-56-1010 Pin Housing Assembly
13 48-76-4008 Quik-Lok Cord Set
14 23-66-2585 Switch
15 28-14-2390 Gearcase
16 28-28-2320 Diaphragm
17 31-15-2030 Handle Halve
18 31-50-2040 Motor Housing
19 32-40-0100 Intermediate Gear
20 32-75-0115 Spindle Gear
21 34-80-2300 Retaining Ring
22 36-66-0125 Intermediate Shaft
23 38-50-5750 Spindle
24 42-14-0460 Baffle Assembly
25 43-44-0985 Gasket
26 44-60-1700 Ground Pin
27 45-04-0750 Chuck Screw
29 45-36-1095 Spindle Spacer
30 45-88-7990 Thrust Washer
SERVICE PARTS LIST
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
1/4 INCH DRILL
CATALOG NO. 0100-20
Cat. No.
31-53-0205
Lock Button Plug
NO. REQ.
(1)
(1)
(1)
(1)
(1)
(1)
(6)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
STARTING
058A
SERIAL NO.
FIG. PART NO.
31 49-15-0265
32 48-66-0070
33 48-66-3200
34 48-66-4080
35 22-84-0845
36 45-30-0030
37 45-30-0035
38 23-52-1610
39 22-18-1310
40 06-75-2850
41 42-68-0800
42 43-62-0845
43 06-54-0325
LUBRICATION (Type "Y" Grease, No. 49-08-5270)
• Place 5 gm. (.02 oz.) of grease on top of the inserted intermediate
ball bearing (1) and on the intermediate pinion (22).
• After inserting all gearing, place 13 gm. (.46 oz.) of grease at the
armature pinion location in the gearcase (15) and fill to the top of
the intermediate gear (19). Grease must contact at least 25% of
the intermediate gear teeth.
Before assembly, lightly coat all press fit areas with
lightweight spindle oil.
FIG. NOTES:
4,20 Support the output ball bearing inside the gearcase before
pressing off the spindle gear.
5,6 Needle bearings to be pressed flush to .010 under flush
from the end which has the vendors identification.
MILWAUKEE ELECTRIC TOOL CORPORATION
13135 W. LISBON RD., BROOKFIELD, WI 53005
BULLETIN NO.
54-06-2800
REVISED BULLETIN
WIRING INSTRUCTION
58-01-1805
EXAMPLE:
00
0 Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
DESCRIPTION OF PART
Side Handle Assembly
1/4 Chuck
Chuck Key
Chuck Key Holder
Fan
Slug
Slug
Brush Spring
Brush Assembly
3/8-16 x 5-1/2 Hex Cap screw
Side Handle Clamp
Side Handle
3/8-16 Square Nut
DATE
Jan. 2003
NO. REQ.
(1)
(1)
(1)
(1)
(1)
(2)
(1)
(2)
(2)
(1)
(1)
(1)
(1)
Drwg. 3