Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Miele NOVOTRONIC W 1612
Summary of Contents for Miele NOVOTRONIC W 1612
- Page 1 Operating instructions Washing machine W 1612 To avoid the risk of personal injury or damage to the appliance, it is en - CA essential that you read these operating instructions before installation and use. This maschine is not approved for use in the United States.
-
Page 2: Caring For The Environment
Caring for the environment Disposal of packing materials The packing materials protect the washer from damage during shipping. They have been selected with an eye to environmental compatibility and efficient disposal, and should be recycled. Returning packaging to the materials cycle helps conserve raw materials and reduces waste. -
Page 3: Table Of Contents
Caring for the environment ......... . 2 Important safety instructions . - Page 4 Installation surface ..........44 Transporting the washer to the installation site ......44 Removing the transport fittings .
- Page 5 The Miele water protection system ........
-
Page 6: Important Safety Instructions
Keep these operating instructions in a safe place and pass them on to any future owner. The W 1612 meets all CSA requirements. This machine is not approved for use in the United States. Proper use... - Page 7 Miele will not be held liable for any damage or harm caused by a missing or incomplete grounding system. For safety reasons, do not use extension cords (danger of fire from overheating).
- Page 8 However, if heavy limescale nonetheless forms on your washer, be sure to select a special descaling agent with corrosion protection. This special product can be obtained from your Miele dealer or from Miele Customer Service. Closely follow the instructions on the product package.
- Page 9 Important safety instructions Accessories Only use accessories that are expressly authorized by Miele. If other parts are used, the appliance warranty and any associated performance and/or product liability claims become null and void.
-
Page 10: Operating The Washing Machine
Operating the washing machine Control panel Display See the following page for more information. Temperature button For selecting a temperature. Spin speed button For selecting the final spin speed or Rinse hold orNo (de-select spin). PC / Optical interface Used by Customer Service for diagnostic checks and programming updates. - Page 11 This can cause an increase or decrease in program times. Programmable functions The programmable functions can be used to adapt the washer to your personal requirements. In programming mode, the display will show the function selected.
-
Page 12: Before Using For The First Time
^ Press the I-On/0-Off button in. If the washer is being switched on for the first time, the welcome screen will appear. The welcome screen will appear in... -
Page 13: Environmentally Friendly Use
Energy and water consumption – To make the most out of each wash load, load the maximum dry weight for the program you have selected. – Use the Colours and Express programs for small loads. – When smaller amounts of laundry are washed using the Normal program, the automatic load recognition system will automatically reduce the... -
Page 14: How To Wash Correctly
Do not rub. Common stains (blood, egg, coffee, tea, etc.) can typically be addressed with the help of the Miele laundry care guide. For a copy, contact Miele directly, or visit the Miele Website. When pre-treating fabrics with... - Page 15 Switch the washer on Load the washer ^ Press theDoor button to open the drum door. ^ Unfold the laundry and load it loosely into the drum. Mixing both large and small items in a load gives better wash results and helps distribute the load evenly during the spin cycle(s).
- Page 16 You will hear a buzzer sound at the end of a program and when Rinse hold is reached. The buzzer continues to ring until the washer is turned off. You can adjust the volume of the buzzer as described in the section on...
- Page 17 Add detergent It is important to use the right amount, because ..too little detergent results in: – the laundry not getting clean, and turning grey and stiff over time – greasy deposits on the laundry –...
-
Page 18: To Start A Program
This can result is shorter or longer program times. The program sequence will also appear in the display. The washer will show which program step is currently running. Remove the laundry when the... -
Page 19: Spin Cycles
1200 removed from the drum upon 1200 program completion. 1200 – Start the final spin: The washer automatically offers you the highest possible spin speed. 1200 However, you can select a lower 1200 speed (RPM). Use the Start/Stop button to start the final spin. -
Page 20: Program Overview
Program overview Normal Fabric T-shirts, underwear, table linens and other such textiles made of cotton, linen, or mixed fibres Note for test institutes: Short program: 3.0 kg load and Short extra option Wrinkle Free Fabric Synthetic fabrics, mixed fibres and easy-care cottons Note: For fabrics that crease easily, reduce the final spin cycle speed. - Page 21 Colours Fabric Mixed loads of garments suitable for the Normal and Wrinkle Free programs. Note: The wash parameters (e.g., water level, wash rhythm and spin speed) are automatically adjusted for each load, to offer the best combination of cleaning and care. Dress Shirts Note: Pre-treat soiled cuffs and collars as needed.
-
Page 22: Extra Options
Extra options The following extras can be added to a program: Normal Wrinkle Free Delicates Woolens Express Colours Dress Shirts Denim/Jeans Darks Short Sensitive Heavy Soil Buzzer... -
Page 23: Garment Care Label Symbols
Washing The number printed on the washtub symbol indicates the maximum wash temperature for the garment. normal agitation normal agitation reduced agitation Hand wash Do not wash Examples for program selection Program Care symbol Normal Wrinkle Free Delicates Woolens Express Colours Garment care label symbols Drying... -
Page 24: Program Sequence
Program sequence Normal Wrinkle Free Delicates Woolens Express Colours Dress Shirts Denim/Jeans Darks Drain/Spin = low water level = medium water level = high water level See the next page for program sequence details. Main wash Water Wash Water level rhythm level –... - Page 25 30 minutes after program completion. Exceptions: In the Woolens program, there is no anti-crease feature. The washer can be opened at any time. For temperature selections from 60°C to 95°C a second rinse will take place. For temperature selections below 60°C there are 3 rinse cycles.
-
Page 26: Changing A Program Sequence
^ Press the Start/Stop button. Cancel program ^ Press the flashing Start/Stop button again. The washer will pump away all the water in the drum. If you wish to remove the laundry: ^ Press the Door button. If you wish to select a different... -
Page 27: Loading Or Removing Laundry
^ Close the door. The program automatically proceeds. Please note: Once a program has started, the washer cannot detect changes to the size of the load. Therefore, if laundry is added or removed, the washer will assume the maximum load. -
Page 28: Detergent
Detergent Selecting the right detergent You can use any detergent designed for automatic washing machines. Consult the package for dosages and instructions. Normal Wrinkle Free Delicates Woolens Express Colours Dress Shirts Denim/Jeans Darks 1) liquid detergent only Universal Colour Liquid detergent especially for woollens Delicates... -
Page 29: Water Softener
I. Washing with several components If you are using several different products in the wash (e.g., special application detergents), Miele recommends loading the products in the following order into compartment 1. Detergent 2. Water softener Total harndess 3. -
Page 30: Fabric Softener, Fabric Shaper, And Liquid Starch
Dyes and dye removers ^ Never use dye removers in this washer. ^ Dyes intended for use in household washing machines may be used. However, please note that the salt used during the dyeing process can cause corrosion to the stainless steel. -
Page 31: Cleaning And Care
Cleaning the housing and control panel Always unplug the appliance before cleaning. NEVER hose down the washer. ^ Use a mild cleanser or soapy water to clean the housing and panel, then dry with a soft cloth. ^ Use a special stainless steel cleaning product to clean the drum. - Page 32 Cleaning and care Cleaning the siphon and softener channel 1. Pull the siphon out of the compartment and rinse under warm running water. Clean the siphon tube the same way. 2. Replace the siphon. ^ Clean the fabric softener channel with warm water and a brush.
-
Page 33: Cleaning The Water Inlet Filters
Cleaning the water inlet filters The water inlet valves are protected by two filter screens. They need to be checked approx. every 6 months. If there are frequent interruptions to the water network, they may need to be checked more frequently. Cleaning the filter in union of the inlet hose ^ Close the tap and unscrew the... -
Page 34: Troubleshooting
– the fuse is in working order. Enter and confirm the pin code. De-activate the pin code if you do not wish the prompt to appear the next time the washer is switched Press any button. This will bring the display back on. -
Page 35: Fault Messages In The Display
The display lights up Technical fault flashes. The display flashes Anti-crease Chk detergent To switch off the fault message: Use the I-On/0-Off button to switch the washer off. Possible cause – The water outlet is restricted or blocked. – The drain hose is sitting too high. -
Page 36: General Problems
It is best to include a mix of large and small items in the washer, so the laundry will distribute evenly. Re- arrange the laundry and start Spin program. – Clean the water inlet filter. -
Page 37: Unsatisfactory Wash Results
Unsatisfactory wash results Problem Liquid detergents usually You used liquid detergent and the do not contain bleaching laundry isn't clean. agents. They may fail to remove fruit, coffee and tea stains.. There is a sticky Not enough detergent grey residue on the was used to break down laundry (fat the grease in heavily... -
Page 38: The Loading Door Cannot Be Opened With The Door Button
To prevent scalding, the door will not open if the suds temperature is higher than 55°C. Remedy Insert the three-pin plug into the socket and/or switch the washer on using the I-On/0-Off button. Switch off the childproofing as described in the section on "Changing a program sequence" under "Safety lock". -
Page 39: Opening The Loading Door (Blocked Drain Outlet And/Or Power Outage)
^ Use it to open the access flap. Troubleshooting Blocked drain outlet If the drain outlet is blocked, up to 25 l will be retained inside the washer. Caution: If laundry has just been washed at a high temperature, water draining out of the machine will still be hot - Beware of scalding!. - Page 40 Troubleshooting Once the flow of water ceases: ^ Pull the drain filter entirely out. ^ Thoroughly clean the filter. ^ Turn the pump blade by hand to check that it moves freely, and remove any foreign objects (buttons, coins, etc.) that are causing an obstruction.
-
Page 41: Customer Service
Warranty conditions and warranty period The washer comes with a two-year warranty. Further warranty information can be found in your warranty booklet. Additional accessories Optional accessories for this washer are available from your Miele dealer or from Miele Customer Service. -
Page 42: Installation And Connection
Installation and connection Front view Inlet hose for hot water Inlet hose for tap water (cold) Power cord Drain hose (with detachable swivel elbow) Detergent dispenser drawer Control panel Loading door Access to drain filter, drain pump, and emergency door release Four height-adjustable feet... -
Page 43: Rear View
Rear view Protruding lid to grip when moving the washer Power cord Inlet hose for hot water Inlet hose for tap water (cold) Installation and connection Drain hose Shipping rod covers Bracket for: – inlet hose – drain hose – power cord Brackets for: –... -
Page 44: Installation Surface
If the washer is being installed on a raised plinth, it MUST be secured against slippage using retaining clips (contact your Miele dealer or Miele Customer Service). Otherwise, the washer may fall off the platform during spinning. - Page 45 ^ Use the combination wrench supplied to turn the left-hand shipping rod 90°, and then ^ pull the rod out. Installation and connection ^ Turn the right-hand shipping rod 90°, ^ pull it out.
-
Page 46: Re-Fitting The Shipping Rods
Make sure that the holes are fitted over the retainers The washer must NOT be moved without the shipping rods in place. Store them as shown or keep in a safe place for future use. They will... -
Page 47: Levelling The Machine
Then turn the counter nut 2 together with the foot 1 to unscrew. Installation and connection ^ Use a level to check that the washer is standing square. ^ Hold the foot 1 securely with a pipe wrench. Now use the combination wrench to screw the counternut 2 firmly back up against the housing. -
Page 48: Installing Under A Countertop
Washer-dryer stack The washer can be stacked with a Miele tumble dryer. A stacking kit will "WTV 412", part# 6 478 870, be required and can be obtained through your Miele dealer or Miele Customer Service. -
Page 49: The Miele Water Protection System
Maintenance and care If the hose ever needs to be replaced, use only a genuine Miele hose - it is tested to withstand pressure of at least 7000 kPa. In order to protect the water inlet... -
Page 50: Tap Water Line (Cold Water)
If the washer is connected to this line only, the appliance will need to be re- programmed to cold water fill only. Please contact your Miele dealer or Miele Customer Service for reprogramming instructions. The second unused inlet hose, with the red tag, will be attached to the rear of the washer after re-programming. -
Page 51: Drainage System
Miele dealer or Miele Customer Service. For delivery heads over 1m (up to a max. of 1.8 m), contact your Miele Customer Service for a replacement pump and with a part # 1053992. Drain hose connection: 1. -
Page 52: Electrical Connection
The proper outlet can be pruchased from a electrical supply dealer. Electrical connection The washer is equipped with a power cord and plug, ready for connection to the power supply. The plug and socket must always be accessible, to facilitate disconnecting the washer from the electrical supply at any time. -
Page 53: Technical Data
Height Width Depth Depth with door open Height for building under Width for building under Weight Maximum floor load Voltage Connected load (watts) Fuse rating Consumption data Min. water flow pressure Max. water flow pressure Inlet hose length Drain hose length Length of power cord Max. -
Page 54: Default Settings
Programmable functions for changing default settings You can use the programmable functions to adjust the electronics to suit changing requirements. Programmable functions can be changed at any time. -
Page 55: Programmable Functions
This second function for the button and selector is not indicated on the panel. Before you begin, check that: – The washer is switched off. – The door is properly closed. Press and hold the Start/Stop button during steps Press the I-On/0-Off button in. -
Page 56: Water Plus
The factory setting for Gentle wash is Off. Suds cooldown With this feature, additional water flows into the washer at the end of the main wash, to cool down the suds. The cooldown feature kicks in with the 95°C and 75°C programs. -
Page 57: Pin Code
Programmable functions ^ Press the Start/Stopbutton. The following appears in the display for confirmation: Code activated Once the washer has switched off, it cannot be used again unless the code is entered. To operate the washer with the pin code When the appliance is switched on, you will be prompted to enter the pin code. -
Page 58: Temperature Unit
Programmable functions Temperature unit You can choose whether temperatures will be displayed in °C/ Celsius or in °F/Fahrenheit. The factory setting is °C/Celsius. Buzzer When the buzzer feature is activated, a signal will be heard when the program ends or when Rinse hold is reached. -
Page 59: Standby Display
The washer drum will continue to rotate at intervals for up to 30 minutes after program completion. You can open the washer at any time to remove the laundry. (Factory setting) The anti-crease feature is activated. - Page 60 Subject to change without notice / 2009 M.-Nr. 07 264 960 / 01...