Miele G 5795 Operating Instructions Manual
Miele G 5795 Operating Instructions Manual

Miele G 5795 Operating Instructions Manual

Miele dishwasher user manual
Hide thumbs Also See for G 5795:

Advertisement

Operating Instructions

Dishwasher
G 5970
G 5975
en - US, CA
To prevent accidents
and appliance damage
read these instructions
before
installation or use.
M.-Nr. 07 909 280

Advertisement

Table of Contents
loading

Summary of Contents for Miele G 5795

  • Page 1: Operating Instructions

    Operating Instructions Dishwasher G 5970 G 5975 en - US, CA To prevent accidents and appliance damage read these instructions before installation or use. M.-Nr. 07 909 280...
  • Page 2: Table Of Contents

    Loading the dishwasher ........
  • Page 3 Problems water intake/drain ......... 59 General problems with the dishwasher ....... . . 61 Sounds .
  • Page 4: Important Safety Instructions

    If the supplied power cord is damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord. The outlet must be accessible at all times after installation to disconnect the...
  • Page 5 The dishwasher must be installed and connected in accordance with the installation instructions. Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. Do not install or use a damaged dishwasher.
  • Page 6 If the supplied power cord is damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord. The outlet must be accessible at all times after installation to disconnect the dishwasher.
  • Page 7 Supervise children near the dishwasher to ensure fingers or other parts of the body are not caught when the Drying Plus feature is in operation. Dishes can be very hot at the end of a program.
  • Page 8: Guide To The Dishwasher

    Guide to the dishwasher Upper spray arm (not visible) Cutlery tray Upper basket Middle spray arm Air inlet for drying (depending on model) Lower spray arm Triple filter system Data plate Optical interface Rinse aid reservoir Dual compartment detergent dispenser...
  • Page 9: Control Panel

    To switch back to the previous menu level or to discard a selected setting. d Delay Start button with indicator This operating instruction manual describes several dishwasher models with different indicated settings. The different dishwasher models are named : Standard = 32 "...
  • Page 10: Caring For The Environment

    For best results follow these tips: ^ For lowest energy consumption you may connect the dishwasher to a cold water source. ^ For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source.
  • Page 11: Before Using For The First Time

    To open the door The door will open automatically at the end of the program to aid in the drying process. This function can be deactivated (see "Settings - Drying Plus"). ^ Pull the handle to open the door. If the door is opened during operation, the rinsing function is automatically canceled.
  • Page 12: Display Function

    – the current time of day – the program sequence – the approximate remaining time – faults and messages To save energy the dishwasher turns off after a few minutes if no button is pressed. To turn the dishwasher back on press K.
  • Page 13: Welcome Screen

    Welcome screen ^ Turn the dishwasher on K. A Welcome screen shows when the washer is turned on for the first time. Language setting The display changes automatically to the language setting. } #eština } dansk ^ Select the desired language and confirm with OK.
  • Page 14 – Your local water authority will be able to advise you of the – The dishwasher must be programmed to correspond to the – In areas where the water hardness fluctuates (e. g. If there is a fault, it will help the service technician to know the hardness of your local water supply.
  • Page 15 The water hardness was programmed at 1 °d (1 gr/gal) by factory default. ^ Select the hardness of your water supply and confirm with the center button. See "Settings - Water hardness" for more information. Before using for the first time Two notes appear in the display.
  • Page 16: Filling The Salt Container

    Filling the salt container To achieve good cleaning results, the dishwasher needs soft water (water that is low in minerals). Hard water results in calcium deposits on dishware and in the dishwasher. Therefore, if your tap water hardness is above 4 °d (4 gr/gal) the water should...
  • Page 17: Salt Refill Message

    The Insufficient salt message is turned off if you have programmed the dishwasher to a water hardness below 4 °d (4 gr/gal). Immediately after each refill, run the "Rinse & Hold" program (without the Turbo function) without a load.
  • Page 18: Rinse Aid

    Before using for the first time Rinse aid Rinse aid helps to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. Filling the rinse aid reservoir with detergent (liquid or powder) will damage the reservoir.
  • Page 19: Rinse Aid Indicator

    The "Refill rinse aid" message will go out. If using "Tab" detergent products in your dishwasher, the messages can be turned off if desired (see "Settings - Deactivate indicators"). If you switch to using detergent that does not contain salt or rinse aid, it...
  • Page 20: Loading The Dishwasher

    Wax, grease and paint will cause permanent discoloration and damage to the dishwasher. ^ Scrape food from dishes before placing them in the dishwasher, rinsing is not necessary. ^ Some foods contain natural dyes, e.g. carrots or tomatoes. Plastic items may discolor permanently if they come in contact with food dyes.
  • Page 21: Items Not Recommended For Dishwashing

    The China & Crystal program*, although extremely gentle and thorough can cause the china and crystal to "wear" if they are not dishwasher safe. Loading the dishwasher Glassware: – There are no standard guidelines for washing glassware, when in doubt wash by hand.
  • Page 22: Typical Load For 10 Place Settings

    Loading the dishwasher Typical load for 10 place settings Upper basket Lower basket Cutlery tray...
  • Page 23: Typical Load For 16 Place Settings

    Loading the dishwasher Typical load for 16 place settings Upper basket Lower basket Cutlery tray...
  • Page 24: Upper Basket

    Loading the dishwasher Upper basket Always use the dishwasher with the upper and lower basket inserted Tall items (except during the program, if available). ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls, etc.
  • Page 25 ^ Pull the cup rack upwards and click it back into position at the required width. Loading the dishwasher Universal support bar The support bar will hold tall glasses and stem ware securely. ^ Fold the bar down and lean the desired glasses against it.
  • Page 26 Loading the dishwasher Adjusting the height: You can set the support bar at two different heights. ^ Pull the support bar upwards and click it back into position at the required height. Use the low setting for small glasses and tumblers.
  • Page 27 ^ Slide out the upper basket. To adjust the upper basket upwards: ^ Lift the basket up until it clicks into place. Loading the dishwasher To adjust the upper basket downwards: ^ Pull up on the levers at the sides of the upper basket.
  • Page 28: Lower Basket

    Glasses, cups, small plates and saucers can also be arranged in the lower basket. Dishwasher with cutlery tray Heavily soiled items ^ Place large platters and dishes in the center of the lower basket. When tilted, plates up to 13 3/4"...
  • Page 29 ^ Slide the hooks of the insert under the struts of the lower basket. ^ Push down on the insert to snap it into position. Loading the dishwasher Glass rack ^ The glass rack can be raised to make more room for tall items.
  • Page 30 Loading the dishwasher Universal support bar The support bar will hold tall glasses and stem-ware securely. ^ Fold the bar down and lean the desired glasses against it. ^ If desired, a section of the cutlery tray can be removed to allow for even taller glasses.
  • Page 31: Cutlery

    The side sections of the tray can be moved into the middle to accommodate tall dishware items in the upper basket. Loading the dishwasher Spoons with thick handles may have to be placed as knives and forks with their heads in the holders.
  • Page 32: Cutlery Basket

    Loading the dishwasher Cutlery basket (depending on model) The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket. ^ To avoid risk of injury, knives and forks should be placed with the handles upwards in the basket.
  • Page 33: Optional Accessories

    ...wash long-stemmed glassware MieleCare Collection Miele branded cleaning and care products, including dishwasher salt, detergent and rinse aid, are available to order from your Miele dealer, Miele or the on-line Miele store www.mieleusa.com Optional accessories the following accessory will need to be ordered...
  • Page 34: Use

    If using a Tab detergent see "Settings - Deactivate indicators". Detergent tabs are not recommended for use with the program "Express" (depending on model). The tabs may not dissolve completely. Dishwasher cleaning products are available from MIele.
  • Page 35: Adding Detergent

    Adding detergent ^ Press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to the compartments and close the container flap. ^ Use one tab or add powder or gel detergent to compartment II and close the flap.
  • Page 36: Turning On

    ^ Open the water supply, if closed. ^ Open the door. ^ Make sure the spray arms can rotate freely. ^ Turn the dishwasher on K. The main menu shows in the display. If the memory function is selected, the last selected program is displayed.
  • Page 37: Program Guide

    Program guide When to use Pots & Pans For normally soiled pots & pans with dried on food, and heavily soiled dishware, use 120% detergent recommended. Normal Program for completely washing a full load of normally soiled dishware with the ability to adjust energy and water consumption based on the soil load of the dishware.
  • Page 38 Starch/Cheese For dishware with dried on starchy or cheesy food; 120% detergent recommended Plastics To gently clean dishwasher safe plastics and plastic toys Tall Items For extra large, heat resistant items, e.g. large vases. Remove upper basket...
  • Page 39: Selecting Options

    Selecting options Options can be added to the selected program. ^ Select the Options menu. The display shows the available options for the selected program. Available options: Turbo: – For shortening the program duration. To achieve optimum results, energy consumption rates will increase. When the "Turbo"...
  • Page 40: Starting A Program

    As long as this reference is shown, tableware can be added to the machine without impairing the cleaning result. The water in the dishwasher is hot, risk of burns by splashing water. Cancel a program only in the first few minutes. Otherwise important program steps (e.g.
  • Page 41: Standby

    Standby mode to save energy. ^ To turn the dishwasher back on press This feature can also be turned off (see "Settings - Optimize standby"). The dishwasher will then turn off after 6 hours.
  • Page 42: Preparing Your Appliance For An Extended Vacation

    To be completely safe, you must turn off the water supply to each individual appliance. This means under the sink for a dishwasher, at the laundry bib for your washer, etc. Interrupting a program A program is interrupted as soon as the door is opened.
  • Page 43: Changing A Program

    Changing a program If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: ^ Open the door. Sensor Wash Main wash ^ Select Cancel and confirm with OK. The program is canceled.
  • Page 44: Additional Options

    Do not use liquid detergent when selecting "Delay Start", the detergent could leak out of the compartment. dishwasher door to prevent children from coming in contact with the detergent. ^ Open the door.
  • Page 45 ^ Close the door. The program starts automatically at the selected time. The indicator , goes out. A few minutes after the last key press, the dishwasher will switch into standby mode to save energy. The display and the indicators will turn off.
  • Page 46: Brilliantlight

    Additional options BrilliantLight The dishwasher is equipped with an interior light. With the door open the light turns off automatically after 15 minutes The light can also be turned off. ^ Open and close the door quickly 3 times. The door must be opened enough so that the interior lighting turns on then off.
  • Page 47: Settings

    The "Settings J" menu allows you to adjust standard settings Opening the Settings J menu ^ Turn the dishwasher on K. The main menu shows in the display. If the memory function is selected, the last selected program is displayed. See "Settings J - Memory". Switch to the main menu by pressing "Clear"...
  • Page 48 Settings Language J The display contents can be shown in different languages. The displayed language can be changed by the submenu "Language J". ^ Select the desired language and confirm with OK. The flag behind the word Language J serves as a guide when an unfamiliar language is selected.
  • Page 49: Water Hardness

    Water hardness Your dishwasher is fitted with a water softener which you need to program to the water hardness level in your area, see "Before the first use". ^ Turn the dishwasher on K. If the memory function is on, the...
  • Page 50: Drying Plus

    Settings Rinse aid For best results the rinse aid dosage can be adjusted. The dosage can be set between 0 and 6 ml. The dosage set by default to 3 ml of rinse aid per program. – Use a higher setting if spots appear on dry glassware.
  • Page 51: Optimize Standby

    Optimize standby A few minutes after the last key is pressed or at the end of the program the dishwasher will switch into Standby mode to save energy. This function can also be turned off. The dishwasher will then turn off completely after 6 hours.
  • Page 52: Reorganize Programs

    Settings Reorganize programs The order of the programs in the program list can be reorganized. The two most frequently used programs can be saved to the first two positions. } Sensor Wash B } Cancel ^ Select with e the program which you would like to save to the first position of the main menu.
  • Page 53: Save Options

    Buzzer in case of a fault The buzzer for a fault sounds continuously. The buzzer sounds up to two minutes if the dishwasher is not turned off or the fault is fixed. The buzzer for a fault cannot be set to off.
  • Page 54: Keypad Tone

    OK. Memory The memory function allows you to save the last selected program. When turning the dishwasher off and on again after a program has finished or opening and closing the door, the last selected program is displayed instead of the main menu.
  • Page 55: Factory Default

    The dishwasher has various demo programs for showrooms. The programs "Demo mode" and "Endless demo mode" show the use and function range of the dishwasher. – Demo mode: The program is started by pressing any button. It runs once and must be started again.
  • Page 56: Remotevision

    Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem.
  • Page 57: Frequently Asked Questions

    Frequently asked questions Possible fault The door is not properly closed. The machine is not plugged in. The fuse has tripped. The dishwasher is not turned on. No program is selected. The fuse has tripped. The reflector was not properly installed. Solution Close the door firmly.
  • Page 58 – Select the desired program. – Close the door. If the problem persists, contact Technical Service. – Turn off the water supply. Contact Miele Technical Service. – Remove the item, if necessary restart the program. If the message shows again contact Miele Technical Service.
  • Page 59: Problems Water Intake/Drain

    Fault in the water intake. – Open the water supply all Solution Open the water supply all the way. Before fixing the fault: – Turn the dishwasher off the way. – Check and clean the water intake filter, see "User Maintenance Instructions".
  • Page 60 – Restart the program. – If the fault is displayed again, use a different program. Before fixing the fault: – Turn the dishwasher off with the K button. – Clean the triple filter. – Clean the drain pump and the non-return valve.
  • Page 61: General Problems With The Dishwasher

    K button. – Turn the interior light on (see "Additional options- BrilliantLight"). – Open the dishwasher door and rearrange items blocking the spray arms. – Turn the dishwasher off K. Then: – Clean the spray arms. See "User Maintenance Instructions".
  • Page 62 Dry the dispenser before adding detergent. Remove the residue. The moisture will evaporate after a short time. Before fixing the fault: – Turn the dishwasher off Clean the triple filter. See "User Maintenance Instructions". Clean the drain pump and the non-return valve, see the "User Maintenance...
  • Page 63: Sounds

    Interrupt the program, and rearrange loose pieces. Remove the foreign object from the drain pump (see "Cleaning the drain pump and non-return valve") This has no effect on the dishwasher. If in doubt, contact a plumber.
  • Page 64: Poor Cleaning Results

    Wash water will run back into the wash cabinet. The rinse aid dosage is set too high. Solution See "Loading the dishwasher". Select a more intensive program (see "Program Guide"). Use the function "Adjust Sensor Wash" (depending on model, see "Settings").
  • Page 65 Problem Possible fault Dishes are not dry, The rinse aid setting may be glasses and too low, or the rinse aid cutlery are reservoir is empty. spotted. Dishes were taken out too soon. A "Tab" product was used. These products have a low drying effect.
  • Page 66 Plastics are discolored. There are rust stains on cutlery. Possible fault Detergent deposits. Glasses are not dishwasher safe. The surface is affected. The wash temperature of the selected program was too low. The detergent has a low bleaching effect.
  • Page 67: After Sales Service

    Miele’s Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home.
  • Page 68: Transport

    Transport To transport the dishwasher, e.g. when moving to a new home, note the following: – Empty the dishwasher. – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – Transport the dishwasher in the upright position. If unavoidable it may be transported on its back.
  • Page 69: User Maintenance Instructions

    User Maintenance Instructions To prevent accidents and appliance damage, read these instructions before installation or use.
  • Page 70: Cleaning And Care

    The wash cabinet can be cleaned with a dishwasher cleaner such as "Dis Cleaner" available from your Miele dealer or online at www.mieleusa.com. Door and the door seal ^ Wipe the door seals regularly with a damp cloth to remove food deposits.
  • Page 71 Indicator reflector The reflector of the optical interface is located in the steam deflector beneath the counter top. ^ Clean as necessary with a damp cloth. Control panel ^ Clean the control panel as necessary with a damp cloth. The appliance front and controls are not scratch proof.
  • Page 72: Triple Filter System

    ^ Confirm with OK. The display changes to the program menu. Cleaning the triple filter ^ Turn off the dishwasher before cleaning. ^ Turn the handle counterclockwise to release the triple filter system, ^ Remove the triple filter from the machine.
  • Page 73 To clean the underside of the filter the flap must be opened. ^ Push the clips together the flap ^ Rinse under running water. ^ Close the flap so that the clip engages. ^ Return the filter so it lies flat in the base of the wash cabinet.
  • Page 74: Cleaning The Spray Arms

    Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present).
  • Page 75: Cleaning The Water Inlet Filter

    If your water contains a large number of insoluble substances, a filter between the water valve and the intake hose connection is recommended. These filters can be purchased from Miele. Cleaning the filter ^ Turn off the dishwasher and pull the plug.
  • Page 76: Cleaning The Drain Pump And Non-Return Valve

    If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system").
  • Page 77: Installation Instructions

    Installation Instructions Please refer to the Installation Diagram supplied with these instructions. To comply with IEC sound testing protocols, please contact Miele for additional instructions. Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.
  • Page 78: Help To Protect The Environment

    Help to protect the environment Disposal of the packing material The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children.
  • Page 79: Electrical Connection

    Danger of overheating! See data plate on the right side of the door. A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician. GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE GROUNDED.
  • Page 80 Electrical connection Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all...
  • Page 81: Plumbing

    Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperature required by the wash program. This allows for connection of the machine to either a hot (max. 140°F / 60°C) or cold water source.
  • Page 82: Drainage

    5 ft (1.5 m) flexible drain hose with an internal diameter of 7/8" (22 mm). – Drain hose extensions and adapters can be ordered from Miele. The maximum drain hose length is 13 ft. (4 m), max. drain height: 39"...
  • Page 84 Alteration rights reserved / 4711 M.-Nr. 07 909 280 / 04 G5970/G5975 / INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.

This manual is also suitable for:

Diamond g 5975 scviG 5975Diamond g 5975 scsf

Table of Contents