WARNING - To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: Read all instructions before using the appliance. Do not dry articles that have been previously cleaned, washed, soaked or spotted with gasoline, dry-cleaning solvents or other flammable or explosive substances.
IMPORTANT SAFETY INSTRUCTIONS GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug.
a e- "PROGRAMS" buttons For selecting a drying program. b "OPTIONS" buttons For selecting a drying option. c "DRYNESS" button For selecting the dryness level of finished laundry. d "STATUS" display Shows the current cycle of the drying program. e "Buzzer" button When selected, a buzzer will sound at the end of a program.
Before loading the dryer The dryer must be correctly installed and connected before the first use. Please refer to the "Installation Instructions". ^ Before using for the first time clean the drum with a cloth. Before drying, check fabric care labels for special drying instructions.
1. Turn on the dryer and load the laundry ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. ^ Load the laundry loosely into the drum. ^ Make sure the lint filters are in place. ^ Close the door with a firm swing - do not push it shut.
Using the dryer Program Normal Available drying options: Turbo, Gentle, Anti-crease Extra Dry Multi-layer fabrics, mixed loads of sturdy cottons, e.g. jeans, towels. More Dry Uniform loads of cotton, e.g. sheets, underwear, socks. Normal Knitted cotton fabrics that may shrink, e.g.
3. Select a drying option (if needed) ^ A drying option can be selected or deselected with each press of the button. Using the dryer OPTIONS Turbo Fast drying for sturdy fabrics with increased temperature and a reduced program length. Gentle For drying delicate fabrics slowly at a lower temperature.
Using the dryer 4. Select the dryness level The dryness level can be selected in the "Normal" and "Wrinkle-free" programs. (The dryness level of the other programs cannot be adjusted.) ^ Press the selection button until the desired indicator illuminates. In the "Wrinkle-free"...
6. Start the program ^ Press the "Start/Stop" button. Once the program starts, the current cycle of the program will be indicated in the "STATUS" display. Using the dryer 7. At the end of a program The "Anti-crease/End" indicator will light at the end of a program and the buzzer will sound if it was selected.
Using the dryer Canceling or changing a program ^ Press and release the "Start/Stop T" button to stop the drying program. To continue drying: ^ Select the new program by pressing the e or - button. ^ Select any desired options. ^ Select a dryness level (available in the "Normal"...
Child lock When activated, the child lock prevents the dryer from being operated by locking the control panel functions. The dryer can be turned on but not started. The "Child lock" indicator will flash. The door can be opened. To activate the child lock 1.
Dryer care Cleaning the lint filter The lint filter must be cleaned after every program. ^ Open the door and remove the lint filter by gently lifting it upwards. ^ Wipe the lint off the filter with your hand (do not use any sharp objects!) ^ Remove the lint from the door frame lint filter with your fingers.
Cleaning the exterior and the control panel To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the dryer.
Dryer care Emptying the condensed water container Depending on the installation, the condensed water will either be pumped to a drain or collected in the condensed water container, located in the upper left corner of the machine. The container holds approximately 1 gallon of water.
Cleaning the condenser To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. Detergent residues, hair and lint in the drying air can penetrate filters and clog the condenser.
Dryer care ^ Turn the condenser lock up. ^ Pull out the condenser. Checking the condenser ^ Hold the condenser against the light. ^ Look through the front and left side (as illustrated above) of the condenser to check for lint. If no lint is visible: ^ Return the condenser.
Cleaning the condenser ^ Rinse the condenser along all sides with warm water as shown in pictures below. ^ Check the condenser for visible soiling. Continue rinsing until the condenser until clean. ^ Check the condenser gasket for soiling. Do not remove or kink the gasket! ^ Place the condenser lengthwise on a towel to air dry.
(see illustration). ^ Flip down the bulb cover. ^ Replace the light bulb with a temperature proof bulb, available from Miele. The light bulb must not exceed the maximum wattage listed on the data plate. ^ Flip up the light bulb cover and press it firmly until it clicks into place.
Quick Guide Remove this guide for easy reference Please read all instructions, especially the "Important Safety Instructions", before using the dryer.
Quick Guide 1.Turn on the dryer and load the laundry ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. ^ Load the laundry into the drum. Make sure that there is enough space in the drum for clothes to tumble freely.
4. Select the dryness level ^ Press the selection button until the desired indicator illuminates. Quick Guide 5. Select the buzzer (if desired) 6. Start the program ^ Press the "Start/Stop" button. 7. At the end of a program The "Anti-crease / End" indicator will light.
Quick Guide Program Normal Available drying options Turbo, Gentle, Anti-crease Extra Dry For laundry to be folded and shelved immediately, e.g. jeans, towels. More Dry For uniform loads, e.g. sheets, underwear, socks. Normal For knitted items that may shrink, e.g. jersey material or lightweight cottons.
What if the dryer will not run? Possible fault The "Start/Stop" button was not pressed. The circuit breaker tripped or the dryer is unplugged. The door is not closed. How do I prevent static cling? Add fabric softener to laundry when washing or select the "Less Dry" setting on the dryer.
Frequently asked questions What if the "Filter/Vent" fault indicator is lit? Possible fault The lint filter is clogged. The air supply in the room is insufficient. What if the program runs too long or stops? Possible fault The airflow is insufficient in the area of the dryer.
In the event of a fault you cannot fix yourself, please contact the Miele Technical Service Department 1-800-999-1360 firstname.lastname@example.org 1-800-565-6435 email@example.com When contacting Technical Service, please quote the model and serial number of your appliance. They can be found on the data plate located below the drum opening.
IMPORTANT SAFETY INSTRUCTIONS Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and could void the warranty. Be sure to observe local building codes. Before installation, disconnect the...
Disposal of the packing materials The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. To prevent suffocation of children, ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
Washer / Dryer Stack The tumble dryer can also be placed on top of a Miele washing machine for a stacked installation. An appropriate stacking kit is required. The stacking kit is available from your Miele dealer or the Miele Technical Service Department.
057B for on-site outlet NEMA 10-30 R 060B for on-site outlet NEMA 14-30 R For more information on the "Easy Installation Kit" or if you have questions concerning the electrical connection, please contact: 1-800-999-1360 firstname.lastname@example.org 1-800-565-6435 email@example.com...
Installation Front view a Power cord with plug b Condensed water container c Control panel d Door (with decor option) e Access panel to condenser f Four height adjustable feet g Optional drain hose: An alternative to using the condensed water container is to drain condensed water into a sink, standpipe or gully.
When the machine lid needs to be removed to reduce the height of the machine, a built under spacer kit* is necessary. It must be installed by a Miele Service Technician. The cover plate of the built under kit replaces the appliance lid and ensures electrical safety.
Installation Installation tips An airflow gap of " (10 mm) must be provided between the machine and the floor. This airflow gap must not be blocked by a toekick or thick piled carpets. Do not install the dryer next to a refrigerator.
Installation Shortening the door panel The door panel can be shortened to match the height of the adjacent cabinetry. The measure X equals the space from the bottom of the washer door to the bottom of the adjacent cabinet. Cut the bottom of the door panel with a jigsaw according to X.
External water drain When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can be drained directly into a drain if the machine is installed near a sink or standpipe so that the condensed water container does not have to be emptied.
Installation If the external drain is not longer used ^ Insert the drain hose into the holder and secure it at the rear dryer top (see holder). ^ Use the clamps at the dryer rear to secure the drain hose.
All rights reserved / 1705 M.-Nr. 06 610 700 / 00...