Subscribe to Our Youtube Channel
Summary of Contents for Microtek 2400 MHz Series
- Page 1 Operations manual MiniLink® Data 900 and 2400 MHz Series MicroTek Electronics, Inc. 25691 Atlantic Ocean Drive, Suite B-3; Lake Forest, CA 92630 Technical Support: 888-366-4276 www.microtekelectronics.com...
-
Page 2: Fcc Notice
FCC NOTICE This equipment has been tested and found to comply with the limits of a Class B device, pursuant to PART 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. -
Page 3: Table Of Contents
SECTION FCC NOTICE ----------------------------------------------------------------- INDUSTRY CANADA NOTICE ----------------------------------------- QUICK START GUIDE ---------------------------------------------------- PRE-INSTALLATION REMINDER, RETURN POLICY --------- TRANSCEIVER DESCRIPTION---------------------------------------- FRONT VIEW ---------------------------------------------------------------- SIDE VIEW ------------------------------------------------------------------- DATA CONNECTIONS----------------------------------------------------- TRANSCEIVER OPERATION ------------------------------------------ TRANSCEIVER SETUP ------------- -------------------------------------- CTU SOFTWARE------------------------------------------------------------ TRANSCEIVER MAINTENANCE--------------------------------------- TRANSCEIVER SPECIFICATIONS ---------------------------------- RF SECTION ----------------------------------------------------------------- DATA SECTION ------------------------------------------------------------- POWER ------------------------------------------------------------------------... -
Page 4: Quick Start Guide
MicroTek toll free at (888) 366-4276 for technical assistance. MicroTek’s toll-free technical assistance is available weekdays from 8 am to 5 pm Pacific Time. -
Page 5: Pre-Installation Reminder, Return Policy
Contact your MicroTek Electronics dealer or distributor to obtain an authorization to return the merchandise for credit. Return authorizations for repair can be sent directly to MicroTek Electronics with a valid RA number. Call our technical assistance line, 1-888-366-4276, to obtain an RA number for repair. -
Page 6: Transceiver Description
TRANSCEIVER DESCRIPTION The MiniLink Data 900/2400 transceivers are either point-to-point or point-to-multi-point units. Software is provided to configure each radio to match the configurations of your camera and controlling device. If the Baud Rate is not set correctly, the control functions will not transmit and the camera will not move accordingly. -
Page 7: Transceiver Operation
Included in each of MicroTek’s environmental enclosure is a piece of double-sided tape that can be used to mount the transceiver inside the housing. - Page 8 TRANSCEIVER OPERATION (Continued) 1. Set-up Tab This screen is used to set the PC Serial Port to interface with the MiniLink Data 900 or 2400 MHz Transceiver. The parameters in this tab must match the PC Serial Port Parameters for communication to be established. 2.
-
Page 9: Transceiver Operation ------------------------------------------ 5
12” x 12” Patch directional antenna with a 10’ cable that connects to the SMA connector. 6. MAINTENANCE Your MicroTek Electronics MiniLink Data Transceiver is an example of superior design and craftsmanship. The following suggestions will help to ensure maximum operational life. -
Page 10: Transceiver Specifications
TRANSCEIVER SPECIFICATIONS RF SECTION Power Output Transmitting Frequency Modulation Channel Capacity Over Air Baud Rate FCC ID Industry Canada Europe DATA SECTION Input Output I/O Data Rate Mode Select MECHANICAL Dimensions Weight Connections POWER Power Requirements ENVIRONMENTAL Humidity Operating Temperature RANGES 3 Miles 7 Miles... -
Page 11: Troubleshooting
6. One or both radios may need to be returned for testing and repair under its 2-year limited warranty. Call MicroTek for return for repair information. 1. Make sure that pins 2 and 3 of the DB9 connector (on the unit not plugged into the PC) are grounded using a paper clip. -
Page 12: Warranty Information
MICROTEK, to be defective in material or workmanship, MICROTEK will repair or replace such part or portion at MICROTEK’s option. The warranty period on the repaired or replaced part or portion of this product shall be limited to the unexpired term of the original warranty.
Need help?
Do you have a question about the 2400 MHz Series and is the answer not in the manual?
Questions and answers