Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for MicroBoards Technology QD-DVD 123
Summary of Contents for MicroBoards Technology QD-DVD 123
- Page 1 QD-DVD MultiDrive Series User’s Manual www.microboards.com Version 1.2...
-
Page 3: Table Of Contents
Table of Contents Introduction... 5 Unpacking your system ... 5 Installation... 5 Basic Instructions ... 5 Buttons and LCD ... 5 Hardware Description... 6 Main Menu ... 7 Functions... 8 Copy ... 8 Test... 8 Test & Copy... 9 Verify ... 9 Compare... -
Page 5: Introduction
Introduction The QD-DVD MultiDrive Series includes the QD-DVD 123, QD-DVD 125, and QD-DVD 127. Each is a high speed, low cost DVD Recordable duplication system from Microboards Technology, LLC. The QD-DVD MultiDrive is perfect for any user requiring easy copying of audio, video, or Data CDs. -
Page 6: Hardware Description
USB Connection, and Controller module. The master discs always go into the DVD reader drive (top). The blank media will always go into the DVD Recorder drives. The power switch and power LED are also located on the front of the QD-DVD MultiDrive duplicator. -
Page 7: Main Menu
Main Menu Source Disc Copying – 52x 1 .0 Copy Analyzing… . 150 .4 MB ▼ Source Disc Testing – 52x 2.0 Test Analyzing… . 150 .4 MB ▼ Source Disc Copying – 52x 3 .0 Test & Copy Analyzing… . 150 .4 MB ▼... -
Page 8: Functions
Verify, Compare, Prescan, Disc Info, Edit Track and Setup. For the Setup options, please refer to pages 14-16. These instructions refer to using 7 DVD recorder drives (available only in the QD-DVD 127), but the QD-DVD MultiDrive will operate using any number of the available recorder drives. -
Page 9: Test & Copy
3. Test & Copy Place your master disc into the DVD reader drive. Place your blank media into the DVD recorder drives. Press the ENT button on the controller interface. The duplicator will now simulate writing to the blank discs. -
Page 10: Compare
5. Compare Place your master disc into the DVD reader drive. Place your copied discs into the DVD recorder drives. Press the ENT button on the controller interface. The duplicator will now compare the copies to the master disc. When completed, the display will... -
Page 11: Disc Info
Disc Info The Disc Info function displays information on the type of master disc placed in the DVD reader drive. To use the Disc Info function, press the ▼▲ buttons until the display reads: 7. Disc Info Place the master disc into the DVD reader drive. Press the ENT button. The source is analyzed. The following screen appears: Source Disc (Analyzing) - Page 12 reads: Select Track: End 1Track 04:53 This screen shows the total number of tracks selected from the master disc and the total time of those tracks. 6. Press the ENT button. The following screen appears: Note: Pressing the ▼ button and selecting NO takes you back to End Edit Disc Editing tracks.
-
Page 13: Close Session
Close Session The Close Session function is used only if you did not close an audio CD, as described in the Edit Track / CD to CD Edit section. You can use this function to manually close the discs. To use the Close Session function, press the ▼▲ buttons until the display reads: 8. -
Page 14: Setup
48x, 40x, 16x, 8x ▲ Options are Off, Note: Option 2 is not used 1 and 2 ▼ in the QD-DVD 123 duplicator ▲ Options are Copy, Test. Test & Copy, Verify, Compare, Prescan, Disc Info, 1.Copy ▼ Edit Track, Setup, Adv Setup ▲... -
Page 15: Language
Language The QD-DVD MultiDrive duplicator has two language options, English and Spanish. English is the default setting. CD Burn Speed The default CD record speed for the QD-DVD MultiDrive is Maximum (48x). The other available record speed options are: 40x, 32x, 24x, 20x, 16x, 10x, and, 4x. Note that some burn speeds are not supported by CD-R media, and will burn at the next lowest supported speed. -
Page 16: Burn Mode
Burn Mode There are 3 options for the Burn Mode setting: 1. DAO (Disc At Once) 2. TAO – Not Close (Track At Once, not closed) 3. TAO (Track At Once, closed) The default setting is DAO. It is recommended that this setting be used. Display Time The display time function is used to display the total record time, after the recording is completed. -
Page 17: Advanced Setup Menu
Advanced Setup Menu 11 -01 Adv Setup 11. Advanced Setup Under Run Protect ▼ 11 -02 Adv Setup Overburn ▼ 11 -03 Adv Setup Read Error Skip ▼ 11 -04 Adv Setup Burn- In ▼ 11 -05 Adv Setup Update Firmware ▼... -
Page 18: Underrun Protect
UnderRun Protect The UnderRun Protect feature allows the recorder to use Burn Proof during recording. This setting defaults to ON and should remain on. This feature protects against making “coasters” or bad discs. Again, this setting should always remain ON. Overburn The default setting for this feature is OFF. -
Page 19: Specifications - Qd-Dvd Multidrive Series
DVD-+R, DVD-+RW, DVD-+R DL, DVD-VIDEO CAUTION: Disconnect AC Power Cord Before Servicing. High Voltages Present with Unit Powered Off and Line Cord Connected. Technical Support For technical questions or support issues, contact Microboards Technology technical support: United States PH: 952-556-1639 FAX: 952-556-1628 support@microboards.com... -
Page 20: Appendix 1 List Of Functions
Appendix 1 List of Functions 1 Copy 2 Test 3 Test & Copy 4 Verify 5 Compare 6 Prescan 7 Disc Info 8 Edit Track (for CD only) 8-1 CD to CD Edit 8-2 Play Audio Track 8-3 Close Session 9 Setup 9-1 Language (Default is English) 9-2 CD Burn Speed (Default is Maximum) -
Page 21: Appendix 2 Lcd Messages
Appendix 2 LCD Messages Normal Conditions: Initialize SDRAM...Initialize the memory of the system. Detect Drives...Detect what drives are connected with the system. User Abort!...Cancel the job during operation. Analyzing...Analyze the source disc. Source Drive Not Ready...Source drive is not ready to read. Target Drive Not Ready...Target drive is not ready to write.