1. Manuals
  2. Brands
  3. MicroBoards Technology Manuals
  4. DVD Recorder
  5. Orbit 3
  6. User manual

MicroBoards Technology Orbit 3 User Manual

Microboards orbit 3 technology users manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
O
r
b
i
t
3
O
r
b
i
t
3

Users Manual

www.microboards.com
Version 1.01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Orbit 3 and is the answer not in the manual?

Questions and answers

Related Manuals for MicroBoards Technology Orbit 3

Summary of Contents for MicroBoards Technology Orbit 3

  • Page 1: Users Manual

    Users Manual www.microboards.com Version 1.01...
  • Page 2 Orbit 3 MICROBOARDS TECHNOLOGY, LLC...

  • Page 3: Table Of Contents

    Microboards Statement Regarding Improper Duplication ... 5 Installation Requirements ... 6 Installing the Input Rods ... 6 Power supply ... 6 Orbit 3 Operation ... 7 The Output Bin... 7 Loading Discs ... 7 Rejected Discs... 7 Main Menu ... 8 Copy ...
  • Page 4 Orbit 3 MICROBOARDS TECHNOLOGY, LLC...

  • Page 5: System Overview

    If any of these items are missing, please contact Microboards Technology Technical Support. IMPORTANT: Please keep all the packing for your Orbit 3 duplicator. If your unit ever needs to be sent in for service, it must be returned in the original packing or the warranty may be voided.

  • Page 6: Installation Requirements

    Orbit 3 Installation Requirements System Setup • Connect the power cable to the Orbit 3 duplicator and plug in to a protected power outlet strip or UPS power supply. • Turn on power to the duplicator. • Install the Input Rods and Output Bin. The system is now ready to use.

  • Page 7: Orbit 3 Operation

    Load the rest of the discs at an angle, against the wide input rod, as seen in figure 2. The Orbit 3 holds a maximum of 100 discs. DO NOT load more than 100 discs in the Orbit 3, as this may cause the discs to feed or unload incorrectly.

  • Page 8: Main Menu

    Orbit 3 The Up and Down Arrow buttons (▲▼) allow you to navigate through the menu without selecting the current menu item. The NO button will move you to the next menu item. YES will select the current menu item.

  • Page 9: Disc-To-Hdd Copy

    Orbit 3 Disc-to-HDD Copy The number of partitions available will depend on the capacity of the hard drive installed in the Orbit 3. If your master is not already on the hard drive, please follow these steps. 1. Press NO or the up or down arrows until the display reads SYSTEM SETUP. Press YES.

  • Page 10: Copy & Compare

    Orbit 3 Copy & Compare Copy and Compare mode will run a comparison of the Master and the new copies prior to unloading the recorder drives. Like Copy mode, the source of the master will depend on the System Setup selections. The same steps are followed as with the standard Copy mode.

  • Page 11: Error Status In Track Extraction

    Press YES to finish extraction and register selected tracks in HDD. Press NO or ▼ to add more tracks from this master data. 7. If you press YES in step 5, the Orbit 3 asks you to register the extracted tracks in HDD. Press YES to start registration.

  • Page 12: Setup Menu

    ▲ (Back), NO, or ▼ (Forward) YES or ESC to return to Menu DELETE? HD 1? HD 2? HD XX*? The number of hard drive partitions available will depend on the capacity of the hard drive installed in the Orbit 3. Complete Updating...

  • Page 13: Accessing The Setup Menu

    Burn Disc Answering NO to this item will set the Orbit 3 in test mode. Duplication will be simulated, with the discs remaining blank. DVD +R media is not compatible with simulation and will be burned during a simulation attempt.

  • Page 14: Drive Status

    (nominal) Applicable Media Occasionally it may be necessary to load updated firmware to the Orbit 3 duplicator. Only those firmware versions recommended and provided by Microboards Technical Support for this specific product should be installed. Installation of an incorrect firmware on any Microboards Technology product may result in any remaining warranty being voided.

  • Page 15: Technical Support

    Orbit 3 For technical questions or support issues, contact Microboards Technology technical support: United States PH: 952-556-1639 FAX: 952-556-1628 support@microboards.com www.microboards.com Please have the Model and Serial Number of your Microboards Product available when contacting Technical Support. Any unauthorized modification to this equipment may result in the revocation by the FCC of the user’s authority to operate this equipment.
  • Page 16 Orbit 3 MICROBOARDS TECHNOLOGY, LLC...

Table of Contents