Related Manuals for Metz 081 NB 1010
Summary of Contents for Metz 081 NB 1010
-
Page 1: Operating Instructions
TV • VIDEO • CAMCORDER • MECABLITZ SAT- Operating Instructions Bedienungsanleitung 081 NB 1010 082 NB 1014 6221-10 083 NB 1018... -
Page 2: Table Of Contents
EUTELSAT (see satellite transmitter table) have been programmed in the factory, ready for use. Chapter „1. SAT Programming“ describes how to quickly assign the desired programs. Your METZ-WERKE Contents Preface ........2 Contents . -
Page 3: Sat Programming
The most popular SAT stations are already stored in this TV set (see the station table). These stations are divided into the following groups: ASTRA TV stations, HOTBIRD TV stations and EUTELSAT TV stations. Each of these groups can be assigned only in its entirety and is sto- red starting at the programme position you specify. - Page 4 Press this key on the remote control return MENU 4. Set the LNC frequencies 6 9 6 - S 0 1 F - G B MENU 5. Select the desired stations (in this example: ASTRA) return MENU 6. Select the first programme position 7.
-
Page 5: Lnc Frequency (50 Hz)
The most popular SAT stations are already stored in this TV set (see the station table). These stations are divided into the following groups: ASTRA TV stations, ASTRA radio stations and EUTELSAT TV stations. Each of these groups can be assigned only in its entirety and is stored starting at the program position you specify. -
Page 6: Transferring Programs (50 Hz)
Press this key on the remote control 4. Select the LNC (necessary return MENU only for multi-switch systems) --/- MENU 6 9 6 + S 0 3 K - G B 5. Select the menu „SAT return MENU program tables“ --/- MENU 6 9 6 + S 0 3 F - G B... -
Page 7: Lnc Power Supply
TV satellites such as ASTRA 1A - D transmit the various programs with vertical (V) or horizontal (H) polarization. If the polarization of your satellite aerial is switched by means of the LNC voltage, you must set the appropriate voltage for each station. The two voltages which are required for selection of the polarization can be set in the menu „LNC power supply“. - Page 8 Press this key on the remote control MENU 4. Set „LNC voltage V“ MENU 5. Store the settings 6. Return to the TV picture 2. LNC Power Supply The screen displays return TV picture Help LNC pwr supply LNC voltage H LNC voltage V --/- MENU...
-
Page 9: Polarizer
In some satellite aerials, horizontal (H) and vertical (V) polarization of the LNC is selected by means of a magnetic polarizer. With this type of aerial, up to 5 current values (polarizer 1..5) are sent via the polarizer socket (on the back of the TV set) to the magnetic polarizer, which then sets the appropriate polarization. -
Page 10: Aerial Control
Depending on the type of satellite aerial you use, there are three methods of aerial control for selection of H and V polarization: • control by means of the LNC voltage (the most common method), • control with the aid of a magnetic polarizer, •... -
Page 11: Relay
Press this key on the remote control 4. Set the polarizer 5. Set the relay control voltage 6. Store the settings and return to the TV picture 4. Aerial Control The screen displays LNC pwr supply: 22 kHz signal: On/Off Polarizer: Relay: On/Off... -
Page 12: Sat Frequency Input / Station Search
A station table is enclosed with the SAT upgrade kit. This station table can, as described in section 1 „SAT programming/Tansferring pro- grams“, be transferred to sequential program positions, starting at a specified position. If the channel assignments of the SAT stations are modified, or if new SAT stations are transmitted, these can be found and stored with the station search function. -
Page 13: Switch Off Afc (Automatic Frequency Control)
When stations are assigned to the various programme positions, they are automatically tuned to the centre frequency. This is normally satisfactory. If the results of this automatic tuning are unsatisfactory, you can turn off the AFC (Automatic Frequency Control) function for specific pro- gramme positions and adjust the tuning manually. -
Page 14: Sat Sound Settings
All parameters for the sound adjustment for a satellite station can be programmed in the submenu „Adj. SAT sound“. These adjustments need to be made only if new stations, whose settings are not stored in the SAT program assignments, are to be received. Press this key on the remote control MENU... -
Page 15: Bandwidth, Deemphasis
Press this key on the remote control MENU 4. Set „Channel 1“ and/or „Channel 2“ 696+S05D-GB MENU 5. Set „Bandwidth“ 6 9 6 + S 0 5 E - G B MENU 6. Set „Deemphasis“ 6 9 6 + S 0 5 F - G B 7. -
Page 16: Picture Adjustment
The Video level adjustment can be used to compensate for the differing modulation levels of various satellite stations and thus to maintain a constant contrast. Under certain circumstances, you may be able to get rid of interference with the Bandwidth adjustment. Press this key on the remote control 1. -
Page 17: Decoder Operation
In general, the video signal is always set to „FBAS“ (composite color signal). If you use a decoder which requires a baseband signal (see operating instructions for your decoder), the video signal must be set to „BB“ (baseband). Press this key on the remote control MENU 1. -
Page 18: Recording Sat Programs
8. Recording SAT Programs In the AV menu, you can define which of the connected AV devices is to supply the picture for the TV screen. Once the settings have been defined, you can switch to standby mode with the term for all external audio/video devices, such as video cassette recorders, camcorders, video disk players, photo CD players, etc., which can be connected to a TV set. - Page 19 The screen displays return TV picture Help AV recording Input Output Video Rec.2 Videorec.2 Video Rec.1 Videorec.1 Decoder A Camcorder Pr 10: 3SAT Pr. 10: 3SAT © 696+S08C-GB A Device connection A Apparaataansluit. return TV picture Help AV recording Input Output Video Rec.2...
-
Page 20: Timer-Controlled Recording Of Sat Programs
9. Timer-controlled Recording of SAT Programs The menu SAT timer recording should be used only if you want to record a SAT program on a video recorder which does not have its own SAT receiver. With this menu, a SAT signal from the TV set can be made available to a simple video recorder without its own SAT receiver. Eight SAT timers can be preset up to two months in advance. -
Page 21: Sat Radio Operation
Many SAT stations use so-called „sound subcarriers“ to transmit additional radio programmes. One SAT station can transmit several additional radio programmes. Some radio stations are already programmed in the factory (see the SAT station table, „ASTRA radio stations“). These can be assigned to programme positions with the aid of the menu „SAT programming“ (see Section 1). Proceed as follows if you wish to programme a new station that is not listed in the SAT station table. - Page 22 Press this key on the remote control MENU 4. Set the sound subcarrier frequency for radio MENU 5. Set the „Bandwidth“ MENU 6. Set the „Deemphasis“ 7. Store the settings and close the menu 10. SAT Radio Operation The screen displays return TV picture TV station table...
-
Page 23: Sat-Adr Radio Operation
11. SAT-ADR Radio Operation The ASTRA satellites also transmit ADR (ASTRA Digital Radio) programmes. The digital transmission of speech and music permits high- quality reception because the signals are not subject to interference. Some ADR stations are already programmed in the factory (see the SAT station table „ASTRA ADR radio stations“). - Page 24 11. SAT-ADR Radio Operation Press this key on the remote control 4. Call sub-menu „SAT sound settings“ and set the sound mode 5. Set the sound subcarrier frequency for radio 6. Store the settings and close the menu ADR-Window The screen displays return picture MENU...
-
Page 25: Technical Data
12. Technical Data RF input range, F-socket input Input frequency range 950 . . .2050 MHz 75 Ω Input impedance: Video: Gain adjustable Frequency range SAT signal also available at the SCART socket while viewing terrestrial programs. Sound: MONO / DUAL / STEREO Sound carrier frequency: 5,00 . -
Page 26: Program Position Management For Sat
14. Program position management for SAT stations If a TV set with 225 program positions is fitted with a SAT upgrade kit 081 NB 1010 or 083 NB 1018, a separate operating level for SAT radio stations is added to the menus. The number of TV stations which can be stored in the TV station table then depends on the number of SAT radio stations stored in the radio station table and vice versa. -
Page 27: Video Recorders
Televisions sets mecablitz electronic flashguns Always first class ! Quality – A matter of principle. With the trend-setting Metz technology you will allways make the correct choice. See your Metz dealer. He will be happy to demonstrate the Video recorders Camcorders Metz-Werke GmbH &...
Need help?
Do you have a question about the 081 NB 1010 and is the answer not in the manual?
Questions and answers