Subscribe to Our Youtube Channel
Related Manuals for METRObility Optical Systems R104-11
Summary of Contents for METRObility Optical Systems R104-11
- Page 1 ETROBILITY PORT 10/100 BASE Installation & User Guide Model: R104-11 ® WITCH...
- Page 2 Metrobility Four-port Switch R104-11 ____ 10/100Mbps Four-Port TX Switch This publication is protected by the copyright laws of the United States and other countries, with all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, translated, transcribed, or transmitted, in any form, or by any means manual, electric, electronic, electromagnetic, mechanical, chemical, optical or otherwise, without prior explicit written permission of Telco Systems.
-
Page 3: Table Of Contents
Product Safety, EMC and Compliance Statements ... 13 Warranty and Servicing ... 14 Metrobility, Metrobility Optical Systems, and NetBeacon are registered trademarks; the Metrobility Optical Systems logo and WebBeacon are trademarks of Telco Systems, a BATM company. All others are trademarks of their respective owners. -
Page 4: Overview
Overview ® The Metrobility R104-11 is a four-port 10/100Mbps TX switch that provides a cost-effective solution for situations in which a simple switching option with few ports is required. When configured for stacking in a Metrobility chassis, the card eliminates the need for any external equipment. This means the network administrator has one less piece of networking hardware to manage and monitor. -
Page 5: Installation Guide
AN4 = OPEN FD = OPEN 100M4 = OPEN AN1 = OPEN AN3 = OPEN 100M1 = OPEN 100M3 = OPEN AN2 = OPEN 100M2 = OPEN 10/100 BASE Metrobility 4- port Switch 5 Port 1 Port 2 Port 3 Port 4... - Page 6 CLOSED position is when the lever is pushed down toward the board. On the rocker DIP switch (SW1), the OPEN position is when the “OPEN” side of the switch is down and the numbered side is up. The CLOSED position is when the numbered side of the switch is down and the “OPEN”...
- Page 7 1 and 2 and enabled on Ports 3 and 4, then Ports 1 and 2 will operate at full duplex, while Ports 3 and 4 will ignore the FD switch setting. The duplex mode for Ports 3 and 4 will be determined through the auto- negotiation process.
- Page 8 AN indicates that auto-negotiation is enabled. + indicates the switch is enabled (OPEN) . — indicates the switch is disabled (CLOSED). A blank space indicates that the switch setting is not applicable and can be either OPEN or CLOSED. Installation Guide l l u —...
-
Page 9: Step 3: Install The Card
The unit is now properly installed and ready for connection to the network. Card Guide 10/100 1000BASE OC-12 10/100 BASE Thumb Screw Card Guide Blank Panel Metrobility 4- port Switch 9 Slot for Management Card 10/100 10/100 10/100 10/100 OC-12 OC-12 OC-12 MGT-10... -
Page 10: Step 4: Connect To The Network
Connect to the Network To connect the R104 to the network, insert the twisted-pair cables into the appropriate connectors. Be sure the card is secured to the chassis by tightening the thumbscrew before making network connections. The R104 provides four shielded RJ-45 connectors that support a maximum segment length of 100 meters. -
Page 11: User Guide
*Refer to the Guide WebBeacon Management Software Installation & User’s Guide n i l n i l n i l Metrobility 4-port Switch d i l n i l d i l n i l i t c t i v only. -
Page 12: Technical Specifications
Technical Specifications Network Connections Twisted-Pair Interface Connector __________________________________ Shielded RJ-45, 8-pin jack Impedance ________________________________________ 100 Ohms nominal Signal Level Output (differential) ________________ 0.95 to 1.05V (100Mbps) ___________________ 2.2 to 2.8V (10Mbps) Signal Level Input ________________________ 200mV minimum (100Mbps) __________________________________ 585mV (10Mbps) Supported Link Length _________________________________________ 100m Cable Type (10Mbps segments) ______________ Category 3, 4 or 5 UTP/STP (100Mbps segments) ______________ Category 5 or 5E UTP/STP... -
Page 13: Product Safety, Emc And Compliance Statements
Canadian Radio Frequency Interference Statement This Class A digital apparatus meets all requirements of the Canadian Interfer- ence-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Réglement sur le matériel brouilleur du Canada. Metrobility 4-port Switch... -
Page 14: Warranty And Servicing
Warranty and Servicing Telco Systems’ Product Warranty TELCO MAKES NO WARRANTIES EXCEPT AS HEREIN SET FORTH: Telco warrants that the equipment and accessories manufactured by Telco, when used in the application and manner for which they are intended, will be free from defects caused by faulty material or poor workmanship from the date of shipment. - Page 15 Purchaser will hold Telco harmless with respect to any claims or actions by third parties. In particular, Telco expressly disclaims and shall in no event be liable for any indirect, special, incidental or consequential damages. Metrobility 4-port Switch...
- Page 16 US Headquarters 2 Hampshire Street Suite 3A Foxboro MA USA 02035 tel: 1.781.551.0300 • fax: 1.781.255.2344 www.telco.com 5660-000023 D 12/06...
Need help?
Do you have a question about the R104-11 and is the answer not in the manual?
Questions and answers