Adjusting The Jog Dial's Midi Message Sending Interval; Adjusting The Sensitivity Of The Jog Dial's Touch Sensor; Mood Lighting Mode - Pioneer DDJ-WEGO Operating Instructions Manual
Dj controller
Hide thumbs
Also See for DDJ-WEGO:
- User manual (3 pages) ,
- Quick start manual (56 pages) ,
- Manual to installation (5 pages)
Table of Contents
Advertisement
Adjusting the jog dial’s MIDI
message sending interval
This unit is equipped with a mode for adjusting the jog dial’s MIDI mes-
sage sending interval.
Depending on your computer’s operating system and specifications, the
jog dial may not operate properly if the sending interval of MIDI mes-
sage for JOG dial is too short. In this case, follow the procedure below to
adjust the MIDI message sending interval.
! The value set in the jog dial MIDI message sending interval adjust-
ment mode is retained even when this unit’s power is turned off.
1 Turn on the power while pressing the right deck’s
[CTRL A] button and [FX1] button.
The unit starts up in the jog dial MIDI message sending interval adjust-
ment mode. Wait until the startup illumination finishes.
2 Press the [SHIFT] button and select the jog dial’s MIDI
message sending interval.
The sending internal changes in units of 1 ms each time the [SHIFT]
button is pressed.
The jog dial’s MIDI message sending interval is indicated by how the
LEDs on the channel level indicator light.
MIDI message
Channel Level Indicator
sending interval
3 ms*
4 ms
5 ms
6 ms
7 ms
8 ms
9 ms
10 ms
11 ms
12 ms
13 ms
*: Setting upon purchase
! When the [PLAY/PAUSE] button is pressed, the jog dial MIDI mes-
sage sending interval adjustment mode is canceled.
Adjusting the sensitivity of the jog
dial’s touch sensor
This unit is equipped with a mode for adjusting the sensitivity of the jog
dial’s touch sensor.
! The value set in the jog dial sensitivity adjustment mode is retained
even when this unit’s power is turned off.
1 Turn on the power while pressing the left deck’s
[CTRL A] and [FX1] buttons.
The unit starts up in the jog dial sensitivity adjustment mode. Wait until
the startup illumination finishes.
2 Press the [SHIFT] button to select the jog dial’s
sensitivity.
The jog dial’s sensitivity changes each time the [SHIFT] button is
pressed.
The jog dial’s sensitivity is indicated by how the
[HOT CUE (DELETE)/SAMPLER] buttons and [SAMPLER] LEDs light.
Jog dial
LED that lights
sensitivity
–4 (low)
Left deck’s [HOT CUE1] button
–3
Left deck’s [HOT CUE2] button
–2
Left deck’s [HOT CUE3] button
–1
Left deck’s [HOT CUE4] button
0*
Left and right decks’ [SAMPLER] button
+1
Right deck’s [HOT CUE1] button
+2
Right deck’s [HOT CUE2] button
+3
Right deck’s [HOT CUE3] button
+4 (high)
Right deck’s [HOT CUE4] button
*: Setting upon purchase
! The jog dial sensitivity adjustment mode is canceled when the
[PLAY/PAUSE] button is pressed.
Mood lighting mode
When this mode is set, the brightness of the illumination of the left and
right jog dials automatically changes slowly. This can be used as mood
lighting.
! This mode can be set even if no DJ application is running.
Launching the mood lighting mode
Press the [SHIFT], [DECK C] and [DECK D] buttons simultaneously.
! The mood lighting mode is set automatically if no operation is per-
formed for 10 minutes.
Canceling the mood lighting mode
Operate any one of the control panel’s buttons, controls, sliders, jog
dials, etc.
Page 17
- Quick Links:
- Installing the Software
- Troubleshooting
Hide quick links:
Advertisement
Table of Contents
